manualshive.com logo in svg

Sports Attack CRICK ATTACK, Instruction Manual, Page: 4 / 17

Share
Download
Sports Attack CRICK ATTACK Instruction Manual Download Page 4

CRICK ATTACK™ CRICKET BOWLING MACHINE

Sports Attack, LLC. 

•

 800.717.4251 

•

 www.sportsattack.com

2

Crick A

ttack

™

 Safety Instructions 

SAFETY INSTRUCTIONS

ELECTRICAL SAFETY

Up to 200 ft. from power source, use a minimum #14/3 grounded 3-wire 15 amp minimum 

rating extension cord.
Over 200 ft. from power source, consult a licensed electrician for required power cord size.

OPERATING SAFETY

CAUTION: Never reach down near moving throwing wheels for any reason! If it is  

necessary to reach into the throwing wheels, ALWAYS:
 

1. Turn all three speed dials to “0”.

 

2. Turn on/off switch “OFF”.

 

3. Unplug Crick Attack from power source

 

4. Wait until the throwing wheels have come to a complete stop before 

                    reaching hands or fingers anywhere near the throwing wheels. 
CAUTION: Carefully check Crick Attack for completeness and condition before  

connecting to electrical power:
 

1. Throwing wheels must be tight on the motor shafts

 

2. Wheel guard and ball chute must be tightly fastened to the throwing head.

Carefully check the throwing wheels frequently for cleanliness, chips and cracks. Do not 

use the machine if the throwing wheels are damaged, or if chips or cracks appear in the 

wheels. (For damage within Warranty period, see Warranty Statement, page i.)
ALWAYS set the speed controls to “0” before connecting the machine to power. Check 

that the speed controls are at “0” before turning the on/off switch “ON”.
Do not allow anyone to walk in front of the machine if it is connected to electrical power.

WARNING

PERSONAL INJURY 

HAZARD

Carefully read all instructions  

in this manual, and all labels 

and warnings on Crick Attack 

before using this machine.
Use machine only under adult  

supervision. Failure to operate 

CrickAttack as described in  

this manual can result in severe 

personal injury or death.
Never loosen the horizontal  

swivel lock while pitching to a  

batter. If the lock is not secure,  

the throwing head could pivot.
A loose swivel lock can allow a  

pitch to be inside which could hit 

the batter.

ELECTRICAL SHOCK 

HAZARD

Crick Attack must be  

connected to a properly 

grounded electrical receptacle.

Do not operate on wet ground.

CAUTION

PERSONAL INJURY 

HAZARD

Keep hands away from throwing 

wheels anytime the machine is  

connected to a power source.
Carefully check Crick Attack for 

completeness and condition 

before connecting to electrical 

power.

 

EQUIPMENT 

ELECTRICAL DAMAGE

Keep hands away from throwing 

wheels anytime the machine is  

connected to a power source.
Carefully check Crick Attack for 

completeness and condition 

before connecting to electrical 

power.

Summary of Contents for CRICK ATTACK


















Reviews:

No comments