SPORTS ART C51R Repair Manual Download Page 74 | Manualshive

Page: 74 / 83

background image

C51R/C51U Bike Repair Manual (Electronics) - Troubleshooting

Troubleshooting

Order Part

Troubleshooting

1 HTR

Handlebar

1. Clean the HTR handlebars.
2. Test the HTR cables.

2 HTR

Cable

1. Inspect whether the HTR handlebar cable is broken or crimped.
2. Test the HTR wire.

3

HTR Board

1. Inspect the LEDs on the HTR board when the handlebars are held.
2. If LED2 does not light, inspect the HTR cable or handlebars.
3. If LED2 lights but LED3 does not flash, the issue is in the HTR board.
4. If LED2 lights and LED4 flashes, but LED5 does not flash (indicating no
output), the HTR board is bad.

5. If you do not hold onto the handlebar but the HTR LED4 flashes, replace the
HTR board.

4

3-pin Cable 1. Inspect wire connections from the HTR board to the display board.

5

Display Board 1. Inspect wire connections.

2. Inspect whether display IC U1 is installed properly.

6-6-3

«
...
72
73
74
75
76
...
»

Summary of Contents for C51R




















































































Reviews:

No comments

Related manuals for C51R

Brand: LifeSpan Pages: 17

Brand: York Fitness Pages: 26

Brand: Orbit Pages: 12

Brand: RAD Cycle Products Pages: 5

Brand: Weslo Pages: 16

Brand: DKN Pages: 36

Brand: Marcy Pages: 27

Brand: Johnson Pages: 28

Brand: PaceMaster Pages: 25

Brand: Diamondback Pages: 40

Brand: CYBEX Pages: 24

Brand: Xebex Fitness Pages: 6

Lifecycle 3500 Series

Brand: Life Fitness Pages: 48

Lifecycle 3500 Series

Brand: Life Fitness Pages: 52

Brand: Wattbike Pages: 12

Brand: Weslo Pages: 16

Brand: TOORX Pages: 12

Brand: Tunturi Pages: 66

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands