10
1-800-732-0144
WWW.SPORTDOG.COM
11
5 . At the end of 15 seconds, or after the second press of the side button, the green light will turn off and the ID/
frequency of the unit will be updated. At this point, the unit will be in the same mode it was in prior to setting
the ID.
6 . Upon changing the ID Code, you will need to match the Collar Receiver to the Remote Transmitter. See Step 5 on
page 11.
NOTE: If you press the side button only once (skipping Step 4) the ID is still a two digit ID. The left digit is defaulted
to 1. For example, if you selected 6 in Step 3 and pressed the button only once, the ID you get will be 16.
To return the unit to the factory ID either remove the battery or follow these steps:
1 . Turn the intensity dial to level 8, flip the toggle switch up, and then press and release the mode button on the
back of your Remote Transmitter. This does not change the mode, so the current mode will still be active after the
ID change is complete.
2 . Do not press any buttons and wait until the green indicator light turns off.
3 . You will now need to match the Collar Receiver to the Remote Transmitter. See Step 5 on page 11.
TOGGLE SWITCH IN THE DOWN POSITION
MODE UPPER BUTTON
FUNCTION
LOWER BUTTON
FUNCTION
SIDE BUTTON
FUNCTION
TOGGLE
SWITCH
(up/down)
NUMBER
OF DOGS
1
Continuous stimulation
(Level set by intensity dial)
Momentary stimulation
(Level set by intensity dial)
Vibration only
Dog 1 /
Dog 2*
2
2
Continuous stimulation
(Level set by intensity dial)
Low Continuous
stimulation (Level set by
intensity dial)
Programmable
Continuous
stimulation**
Dog 1 /
Dog 2*
2
3
Continuous stimulation
(Level set by intensity dial)
Tone w/ one second delay
Continuous stimulation
Vibration only
Dog 1 /
Dog 2*
2
4
Continuous stimulation
(Level set by intensity dial)
Low Continuous
stimulation (Level set by
intensity dial)
Vibration only
Continuous/
Momentary
1
5
Dog 1 (Level set by
intensity dial)
Dog 2 (Level set by
intensity dial)
Dog 3 (Level set
by intensity dial)
Continuous/
Vibration
3
6
Continuous stimulation
(Level set by intensity dial)
Tone only
Vibration only
Dog 1 /
Dog 2*
2
7
Continuous stimulation
(Level set by intensity dial)
Vibration only
N/A
Dog 1 /
Dog 2*
2
8
N/A
N/A
N/A
N/A
N/A
NOTE: Modes 1, 3, 5 ,6 and 7 provide 8 levels of stimulation, which correspond to the setting of the Intensity Dial.
Modes 2 and 4 provide more “increments” to choose from – a total of 16 levels of stimulation. For example, in mode
2 with the Intensity Dial set at 2, the lower button provides level 3 of 16 and the upper button provides level 4 of 16.
* For Two-Dog operation setup refer to Step 6 below.
** After selecting mode 2 and while the green indicator light is still solid in color, turn the intensity
dial to the desired Continuous Stimulation level and press the side button to set the level. The
green light will quickly flash acknowledging your selection. For example, if you turned the intensity
dial to 3, the side button on your Remote Transmitter will transmit Continuous Stimulation at level 3
when pressed. If no level is selected after 15 seconds, it will default to level 8.
MATCH THE COLLAR RECEIVER AND REMOTE TRANSMITTER
To reset the Collar Receiver to work with a new Remote Transmitter or to reprogram a new Collar Receiver
to work with your existing Remote Transmitter:
A. Turn the Collar Receiver off.
B. Press and hold the On/Off Button. The Receiver Indicator Light will come on, then turn off after 5-6
seconds. If the On/Off Button is released too early, the Receiver Indicator Light will begin flashing as
normal. If this occurs, start over and repeat from
A
.
C. After the Receiver Indicator Light has turned off, release the On/Off Button.
D. Press and hold the Upper Button on the Remote Transmitter until the Receiver Indicator Light
flashes 5 times. You may need to hold both units 2-3 feet from each other before this occurs. Once
the Receiver Indicator Light has flashed 5 times, the Collar Receiver has been reset and will begin
flashing as normal. If the Receiver Indicator Light does not flash 5 times, start over and repeat
from
A
.
PROGRAM THE SYSTEM FOR TWO-DOG OPERATION
SportDOG
™
Collar Receivers can be set to respond to either the
up
or
down
toggle switch position.
A SportDOG Add-A-Dog
®
Collar Receiver must be purchased to train a second dog in two-dog mode.
Please refer to the back cover for compatible Add-A-Dog Collar Receivers for this system.
TOGGLE SET TO UP
POSITION FOR DOG 1 OR
TOGGLE SET TO DOWN
POSITION FOR DOG 2
1. Program the Remote Transmitter to mode 1,4,5 or 7 in the toggle
up
position or mode 1,2,3,6 or 7 in the toggle
down
position (see
pages 9-10).
2. Then flip the toggle switch to the
up
position to program the first
Collar Receiver.
A.
Turn the Collar Receiver off.
B.
Press and hold the On/Off Button. The Receiver Indicator Light
will come on, then turn off in 4-5 seconds. If the On/Off Button
is released too early, the Receiver Indicator Light will begin its
normal flashing. If this occurs, start over and repeat from
A
.
C.
After the Receiver Indicator Light has turned off, release the
On/Off Button.
D.
Press and hold the Upper Button on the Remote Transmitter
until the Receiver Indicator Light flashes 5 times.
3. Program the second Collar Receiver the same way using
A
through
D
above, but with the toggle
switch in the
down
position
.
S
TE
P
::
05
S
TE
P
::
06
400-1123-1.indd 10-11
6/22/09 11:29:50 AM
