8
1-866-748-6748
www.sitmeanssit.com 9
Fit the Collar Receiver
Important: The proper fit and placement of the Collar Receiver is important for
effective training. The Contact Points must have direct contact with your dog’s skin.
To ensure a proper fit, follow these steps:
1. With your dog standing (3A), center the Collar Receiver so the Contact
Points are underneath your dog’s neck, touching the skin (
3B). If your
dog has a long or thick coat, you have two options to ensure consistent
contact: either trim the hair around the Contact Points or switch to the
longer Contact Points included with your system.
3A
2. The Collar Receiver should fit snugly, yet loose enough to
allow one finger to fit between the strap and your dog’s
neck (
3C).
3. Allow your dog to wear the collar for several minutes,
and then recheck the fit. Check the fit again as your dog
becomes more comfortable wearing the Collar Receiver.
3B
Care and Cleaning
To ensure the effectiveness of this product and the
comfort and safety of your dog, check the fit of his
collar frequently. This Guide describes proper collar
fitting. If you notice that your dog is experiencing
skin irritation, discontinue use of the collar for a few
days. If the condition persists beyond 48 hours, see
your veterinarian.
3C
To prevent skin irritation from occurring:
• The Collar Receiver should not be worn for more than 8 hours out of every 24-hour period.
• Your dog’s neck and the Contact Points must be washed weekly with a washcloth and mild
hand soap, then rinsed thoroughly.
_____________________________________________________________
Program the Remote Transmitter
Note: The Transmitter is factory set to mode 6. The mode of the Remote Transmitter can be
changed to fit your type or style of training.
To change the mode:
1. Referring to the table on the following page, adjust the Intensity Dial to the mode you want
to use.
2. Turn the Remote Transmitter over.
3. With a pen or the tine on the buckle of your collar strap, depress and release the mode
button. When the mode button is pressed, the Transmitter Indicator Light will be solid in
color. When it is released, it will flash the mode selected.
For example, if mode 5 is desired, adjust the Intensity Dial to Level
5. Once the mode button has been depressed, the Transmitter
Indicator Light will be solid, and once the mode button is released,
the Transmitter Indicator Light will flash five times.
Note: Continuous Stimulation will transmit for no more than 8
continuous seconds no matter how long the button is pressed. To
reactivate, release and repress the button.
Mode
Upper Button
Function
Lower Button
Function
Side Button
Function
# of
Dogs
1
Momentary
High Stimulation
(Level set by knob)
Momentary
Low Stimulation
(Level set by knob)
Continuous
High Stimulation
(Level set by knob)
1
2
Momentary
High Stimulation
(Level set by knob)
Momentary
Low Stimulation
(Level set by knob)
Continuous
Low Stimulation
(Level set by knob)
1
3
Continuous
High Stimulation
(Level set by knob)
Continuous
Low Stimulation
(Level set by knob)
Momentary
High Stimulation
(Level set by knob)
1
4
Dog 1
Continuous
Low Stimulation
(Level set by knob)
Dog 2
Continuous
Low Stimulation
(Level set by knob)
Dog 3
Continuous
Low Stimulation
(Level set by knob)
3
5
Dog 1
Momentary
Low Stimulation
(Level set by knob)
Dog 2
Momentary
Low Stimulation
(Level set by knob)
Dog 3
Momentary
Low Stimulation
(Level set by knob)
3
6
Continuous
High Stimulation
(Level set by knob)
Continuous
Low Stimulation
(Level set by knob)
Momentary
Low Stimulation
(Level set by knob)
1
7
Continuous
Low Stimulation
(Level set by knob)
Momentary
Low Stimulation
(Level set by knob)
Tone only
1
Note: Modes 4, 5 and 7 provide 8 levels of stimulation, which correspond to the setting of the
Intensity Dial. Modes 1, 2, 3 and 6 provide more “increments” to choose from -- a total of 16 levels
of stimulation. For example, in mode 6 with the Intensity Dial set at 2, the bottom button provides
level 3 of 16 and the top button provides level 4 of 16.
______________________________________________________________________________
Match the Collar Receiver and the
Remote Transmitter
To reset the Collar Receiver to work with a new Remote Transmitter or to reprogram a
new Collar Receiver to work with your existing Remote Transmitter:
A. Turn the Collar Receiver off.
B. Press and hold the On/Off Button. The Receiver Indicator Light will come on, then
turn off after 4-5 seconds. If the On/Off Button is released too early, the Receiver
Indicator Light will begin flashing as normal. If this occurs, start over and repeat
from
A.
C. After the Receiver Indicator Light has turned off, release the On/Off Button.
D. Press and hold the Upper Button on the Remote Transmitter until the Receiver
Indicator Light flashes 5 times. You may need to hold both units 2-3 feet from each
other before this occurs. Once the Receiver Indicator Light has flashed 5 times, the
Collar Receiver has been reset and will begin flashing as normal. If the Receiver
Indicator Light does not flash 5 times, start over and repeat from
A.
Step
4
Step
3
Step
5
400-931-1.indd 8-9
1/3/12 1:49 PM
