SPM IPro Operator'S Manual Download Page 23

Page: 23 / 23

Edition:

October, 2018

Revision:

Pag. :

46/76

message appears on the

capacitive touch panel

cleaned



The unit is positioned too close to a wall

or other object restricting air flow and

causing the machine to run at a higher

temperature



The filter is not properly installed



The unit has been installed near a heat

source, such as a coffee machine, ice

maker or cold beverage machine which

expels hot air from its vents, causing the

machine to run at a high temperature.

instructions



Reposition unit to maximize

ventilation space (see

installation figures)



Properly install filter see



Reposition unit to maximize

ventilation space (see

installation figures)

Board error code

Possible cause

Solution

E14 or E24 or E34 message

appears on the capacitive

touch panel display.

1, 2 e 3 are respectively the

left, centre and right bowls.



The product consistency is too high



An ice block is obstructing the auger

rotation



Reduce the product consistency



Remove ice blocks

E15 or E25 or E35 message

appears on the capacitive

touch panel display.

1, 2 e 3 are respectively the

left, centre and right bowls.



An ice block is blocking the auger

rotation



The gear motor is defective



Remove ice blocks



Replace the gear motor

E11 or E21 or E31 message

appears on the capacitive

touch panel display.

1, 2 e 3 are respectively the

left, centre and right bowls.



The

temperature

probe

the

corresponding bowl is short circuited.



Check and replace the probe

E12 or E22 or E32 message

appears on the capacitive

touch panel display.

1, 2 e 3 are respectively the

left, centre and right bowls.



The

temperature

probe

the

corresponding bowl is disconnected.



Check and connect the probe

E01 or E04 or E05 or E06

message appears on the

capacitive

touch

panel

display.



The control board is defective



Replace the board

E02 message appears on the

capacitive

touch

panel

display.



The condenser temperature probe is

short circuited.



Check and replace the condenser

probe

E03 message appears on the

capacitive

touch

panel

display.



The condenser temperature probe is

disconnected.



Check

and

connect

the

condenser probe

Summary of Contents for IPro
























Search results

Summary of Contents for IPro

Reviews:

Related manuals for IPro

Brands by name

Popular brands

SPM IPro, Operator'S Manual

Search results

Summary of Contents for IPro

Reviews:

Related manuals for IPro

Brands by name

Popular brands