Split Phantom ULB21-DLP Installation And Instruction Manual Download Page 13

Page: 13 / 20

-12-

Wiring

For proper installation and full operability, this light requires a 10.5A ignition
switched power source, connections to the negative terminal of the battery,
and four external switches rated for a minimum 1A

(user supplied)

These lights come with a pre-installed 6-conductor harness. In addition, the cable
also contains a bare drain wire and foil shielding.

BLACK

BARE

Orange w/Red

Flashing Warning Lights

Steady Burn Warning Lights

Green w/Red

White w/Brown

Pursuit Lights (Flashing DLP)

Green w/Yellow

Takedown Lights (Steady Burn DLP)

Warning Lights

DLP

Lights

Ignition Sw12VDC

Red

User Supplied Switches

10 AMP

FUSE

Wire

Function

Bare

Ground

Black

Ground

Red

Power to light

(+12VDC ignition switched – 10.5A)

Orange w/Red

Warning LED Flashing Mode

Green w/Red

Warning LED Steady Burn (and Burst)

White w/Brown

DLP LED Pursuit Mode

Green w/Yellow

DLP LED Takedown Mode (Steady Burn)

Quick Wiring Guide

All wires connected to the positive terminal of the battery should be fused at the
battery for their rated load.

Testing the light before this fuse is properly

installed will void the warranty on the light.

Summary of Contents for ULB21-DLP





















Search results

Summary of Contents for ULB21-DLP

Reviews:

Related manuals for ULB21-DLP

Brands by name

Popular brands

Split Phantom ULB21-DLP, Installation And Instruction Manual

Search results

Summary of Contents for ULB21-DLP

Reviews:

Related manuals for ULB21-DLP

Brands by name

Popular brands