manualshive.com logo in svg

Splicecom Maximiser, Installation And Reference Manual

The Splicecom Maximiser User Manual is a comprehensive guide that enables users to fully utilize the product's features. Easily accessible, it is available for free download from our website, offering a step-by-step manual to help you optimize the Splicecom Maximiser's capabilities.

Share
Download
background image

Installation and Reference Manual

 

 

 

System Operation 
Installation and Reference Manual v3.2/0410/6 

 

51 

 

Default Dial Plan entries 

The PCS 10 is supplied with 10 pre-programmed buttons which dial specific dial plan entries.  Therefore 
the User assigned to the PCS 10 must be configured with a Dial Plan containing these default dial plan 
entries.  For details on working with Dial Plans please refer to page 114 and, within this section, details on 
using the default dial plan entries from page 121. 
 

Connecting a PCS 505 or PCS 5 

When connecting a PCS 505 or PCS 5 to an analogue port the following should be considered: 
 

Caller Display Type 

The Default Caller Display Type for an analogue port uses the Caller Display Type required for use with the 
PCS 505 or PCS 5 however if the handset is to support the Message Waiting light the Lamp Caller Display 
Type should be used.  For details on how to configure an Analogue Extension port please refer to 
page 77. 
 

Default Dial Plan entries 

The PCS 505 and PCS 5 are supplied with a System Feature Guide displayed on the handset detailing the 
use of specific dial plan entries.  Therefore if the User is going to utilize these dial plan entries the User 
must be configured with a Dial Plan containing these entries.  For details on working with Dial Plans 
please refer to page 114 and, within this section, details on using the default dial plan entries from 
page 121. 

Connecting a PCS IP Phone 

Power over Ethernet considerations 

 
Power to the PCS 580G, PCS 570G/570, PCS 560, PCS 410/400 and PCS 100 is provided by Power over 
Ethernet (PoE).  This can be supplied by a third party PoE switch or by the following methods: 
 

•

 

PCS 580/570/560 – via one of the PoE LAN ports on a Call Server or Phone Module, or via a Single 
Terminal Ethernet Power Supply (STEPS) 

•

 

PCS 410/100 - via one of the PoE LAN ports on a Call server or Phone Module, or via a Single Terminal 
Ethernet Power Supply (STEPS) 

•

 

PCS 400 - via one of the PoE LAN ports on a Call server or Phone Module, or via a Single Terminal 
Ethernet Power Supply (STEPS).  The PCS 400 can also obtain power via a PCS PSU when it is not 
practical to use PoE.  Please note that if a PCS 400 is connected to a PoE LAN port on a 5100 or 5108 
Call Server the PCMCIA card cannot be used. 

 
Please note that if a STEPS is used with a PCS 580G or PCS 570G the LAN port (port 1) will not run at 1G. 
 
PoE LAN ports are provided as follows: 
 
5100 Call Server, 5108 Call Server and 5300 Phone Module – provides 4 x PoE LAN ports supporting the 
following combinations: 

1 x PCS 580G or 
1 x 410/400 or  
up to 2 x PCS 570G/570 or 
up to 4 x PCS 100/PCS 560 or 
up to 1 x PCS 570 and 2 x PCS 100/PCS 560 

Summary of Contents for Maximiser













































































































































































































































































































































































Reviews:

No comments

Related manuals for Maximiser

Xblue Networks SP2014 Manual preview
SP2014
Brand: Xblue Networks Pages: 60
Xblue Networks X16 Quick Start Manual preview
X16
Brand: Xblue Networks Pages: 2
Xblue Networks X-50 Installation Manual preview
X-50
Brand: Xblue Networks Pages: 260
Xblue Networks X16 Manual preview
X16
Brand: Xblue Networks Pages: 2
Xblue Networks X16 User Manual preview
X16
Brand: Xblue Networks Pages: 52
PHOTON AWP-AE80I User Manual preview
AWP-AE80I
Brand: PHOTON Pages: 48
Binatone SYMPHONY 3325 User Manual preview
SYMPHONY 3325
Brand: Binatone Pages: 2
Ciro Cybercharger Quick Start Manual preview
Cybercharger
Brand: Ciro Pages: 2
Southwestern Bell GH3080 Owner'S Manual preview
GH3080
Brand: Southwestern Bell Pages: 24
Net2Phone Yap Phone User Manual preview
Yap Phone
Brand: Net2Phone Pages: 20
RCA 25255RE2 - ViSYS Cordless Phone Base Station Specifications preview
25255RE2 - ViSYS Cordless Phone Base Station
Brand: RCA Pages: 2
Gigaset DL500a Manual preview
DL500a
Brand: Gigaset Pages: 137
Philips TD9363 User Manual preview
TD9363
Brand: Philips Pages: 2
Philips Lifeline CarePartner 9500 Quick Start Manual preview
Lifeline CarePartner 9500
Brand: Philips Pages: 6
Philips Kala 6523 User Manual preview
Kala 6523
Brand: Philips Pages: 9
Philips Kala User Manual preview
Kala
Brand: Philips Pages: 15
Philips M110 User Manual preview
M110
Brand: Philips Pages: 28
Philips Onis User Manual preview
Onis
Brand: Philips Pages: 36

Brands by name

Popular brands

Load more brands