background image

5

Technical data

Model

WDV2200XCD

Dimensions

width: 23.4” (59.5 cm)

height: 33.24” - 33.75” (84.5 - 85.7 cm)

depth: 22” (55.9 cm)

Weight

148 lbs

Minimum Instal-

lation Clearances

Sides: 0”

Front / Back: 1”

Top: 0”

Capacity

Washing: 2 to 15 lbs. (1 to 7 kg)

Drying: 2 to 11 lbs (1 to 5 kg)

ELECTRICAL

• Machine Voltage/Amperage - 120V, 60 Hz, 

12.5 Amp.

• Connection - 3-prong plug with 6’ cord is provided with the machine.

TECHNICAL INFORMATION

• Circuit/Protector - 3-wire single phase, 120V, 60 Hz, AC, on a separate

15 Amp branch circuit.

Electrical connec-

tions

Voltage: 120Volts, 12.5 Amp, 60 Hz

Water connec-

tions

Max. Pressure: 0.69 MPa (6.9 bar), 100 psi

Min. Pressure: 0.05 MPa (0.5 bar), 7.5 psi

Max. Spin speed

up to 1200 RPM

This appliance was tested by UL and 

conforms with both Canadian and U.S. 

UL safety requirements and displays their Mark.

C

UL

US  LISTED

®

The model number and serial number of this machine may be found on the label attached to the front panel behind the door, and also on the 

label attached to the rear panel. 

You should note the model and serial numbers of this unit in the space provided. Retain this booklet as a permanent record of your purchase to 

aid in identification in the event of theft.

MODEL N.

SERIAL N.

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in 
death, fire, or electrical shock.

If you have...

You’ll need...

no access to Hot/Cold water hookups

Splendide Faucet Adapter Kit, or equivalent.

to install a dryer vent and ducting in your 

RV or boat

Splendide Vent Kit, or equivalent.

concerns about the appliance shifting in 

your RV or boat

Splendide SecureFit braket kit,or equivalent.

water damage concerns

Splendide Drain-A-Way Pan, or equivalent.

to make a 90° duct turn in less than 4.5”

Splendide 90° offset elbow, or equivalent

UNDER SINK METHOD

1.

 Cut the blocked end of the under sink 

drainage unit.

2.

 Fix the hooked end support a minimum 

of 24.4” (620 mm) from the floor.

3.

 Use a hose clip clamp to securely attach 

the grey drainage hose end to the under 

sink drainage unit using a hose clamp.

Summary of Contents for WDV2200XCD















Reviews: