SPL Track One 2058 Manual Download Page 16

16

Display: PPM Output

The PPM Output display shows the peak reading of the output level (cali-

brated to 0 dB) and is present at the analog outputs on the rear of the unit. This 
display also serves to the pre-amplifying Gain. The value ”+12 dBu” marked on 
the right side represents the maximum level of the optional AD/DA converter 
which should not be exceeded. (Further information is given in the directions 
to the AD/DA converter).

Although  the  values  of  the  PPM  Output  display  only  cover  up  to  +  12 dB 

sufficient headroom remains internally (approximately 6 dB) so that the output 
value  can  exceed  this  limit  without  causing  clipping.  The  range  of  optimal 
noise performance lies between 0 and + 9 dB.

Display: Gain Reduction

The Gain Reduction display provides information about the processing being 

undertaken with the Compressor/Limiter or the Noise Gate. The level change, 
perhaps caused by compression, are scaled in 1.5 dB steps. The display is acti-
vated when the Compressor/Limiter module is switched on.

Built around a torroidal transformer, the power supply allows for a minimal 

electromagnetic field with no hum or mechanical noise.  The power supply‘s 
output side is filtered by an RC circuit to extract noise and hums caused by 
your power service. 6000 µf capacitors smooth out the positive and negative 
half waves. 

The phantom power is derived with a precise current regulator to provide a 

clean phantom power of 48 volts. Our high quality 0.1 % / 6,81 kOhm resistors 
ensure the pristine quality of the phantom power supply. 

The  supply  voltage  can  be  set  to  230 V/50 Hz  or  115  V/60 Hz.  Check  your 

country‘s power requirements for the appropriate setting. An AC power cord 
is included to feed the IEC-spec, 3-prong connector. Transformer, AC cord and 
IEC-receptacle are VDE, UL and CSA approved. The main fuse is rated at 315 mA 
for 230 v and 630 mA for 115 v.

Chassis  ground  and  AC  ground  can  be  physically  disconnected  by  the 

“Ground Lift” switch (Gnd Lift). This helps to eliminate hums.

Control Elements

Output/Display

Power Supply

All manuals and user guides at all-guides.com

all-guides.com

Summary of Contents for Track One 2058





















Reviews: