background image

8

RackPack 4

Air Circulation

Always ensure sufficient air circulation in any installation or setup: always keep a distance of 
about 4-5 cm (1 U rack space or about 2 inches) to the next device. This concerns especially 
the space above and below the device because louvers are cut into top and bottom panels for 
optimal heat removal.

For free placement outside of a rack please always use a level and stable surface. Never place 
it on a soft surface such as a blanket or a cushion etc. 

If the RackPack 4 is mounted into a rack, do not place units below the RackPack 4 that produce 
excessive heat.

Power Connection

Always  make  sure  that  the  position  of  the  voltage  selector  on  the  back  of  the  RackPack 4 
corresponds to the voltage of your local power supply (115 V position: 110-120 V, 230 V posi-
tion: 220-240 V). In case of doubt please ask your dealer, a professional electrician or your 
local power supplier.

Before you make or change any power or signal connections, turn off all connected devices 
including the RackPack 4, and mind all security advices on pages 4 and 5. 

Signal Connections 

Before first connecting any other equipment – and in all other cases where you are connecting 
cables with or from other sources – you should be sure to shut the unit and all machines to be 
connected off. Otherwise you risk to damage the unit, connected gear or your ears.

On And Off

In switching on and off, you do not need to follow any particular sequence with connected 
devices in the periphery of the RackPack 4. There is, however, the general rule for a chain of 
devices in the audio processing to always turn on power amplifiers last and to turn them off 
first. If specified sufficiently you can also switch the external power supply on and off through 
a multiway connector or other main switches.

Hook Up

Summary of Contents for RackPack 4

















Reviews: