background image

26

Warranty

SPL electronics GmbH (hereafter called SPL) products are warranted only in
the country where purchased, through the authorized SPL distributor in that
country, against defects in material or workmanship. The specific period of
this limited warranty shall be that which is described to the original retail
purchaser by the authorized SPL dealer or distributor at the time of
purchase.

SPL does not, however, warrant its products against any and all defects:

1) arising out of materials or workmanship not provided or furnished by SPL,
or 2) resulting from abnormal use of the product or use in violation of
instructions, or 3) in products repaired or serviced by other than authorized
SPL repair facilities, or 4) in products with removed or defaced serial
numbers, or 5) in components or parts or products expressly warranted by
another manufacturer.

SPL agrees, through the applicable authorized distributor, to repair or
replace defects covered by this limited warranty with parts or products of
original or improved design, at its option in each respect, if the defective
product is shipped prior to the end of the warranty period to the designated
authorized SPL warranty repair facility in the country where purchased, or to
the SPL factory in Germany, in the original packaging or a replacement
supplied by SPL, with all transportation costs and full insurance paid each
way by the purchaser or owner.

All remedies and the measure of damages are limited to the above services.
It is possible that economic loss or injury to person or property may result
from the failure of the product; however, even if SPL has been advised of this
possibility, this limited warranty does not cover any such consequential or
incidental damages. Some states or countries do not allow the limitations or
exclusion of incidental or consequential damages, so the above limitation
may not apply to you.

Any and all warranties, express or implied, arising by law, course of dealing,
course of performance, usage of trade, or otherwise, including but not
limited to implied warranties of merchantability and fitness for particular,
are limited to a period of 1 (one) year from either the date of manufacture.
Some states or countries do not allow limitations on how long an implied
warranty lasts, so the above limitations may not apply to you.

This limited warranty gives you specific legal rights, and you may also have
other rights which vary from state to state, country to country.

SPL electronics GmbH

41372 Niederkruechten, Germany

Summary of Contents for 9945





























Reviews: