background image

22

Specifications

Measurements

Microphone Input

Frequency Response: ..................................... 10 Hz-100 kHz 
(100 kHz = -3 dB)

Common Mode Rejection: ............................ 1 kHz: -80 dB / 10 kHz: -78 dB
(@ -20 dBu)

THD & N: .............................................................. Amplification:

A weighted:

20 dB

-97,1 dBu

40 dB

-91,1 dBu

65 dB

-69,4 dBu

Dynamic Response: ........................................ 118 dB

Line / Instrument Input

Frequency Response: ..................................... 10 Hz-100 kHz 
(100 kHz = -3 dB)

Common Mode Rejection: ............................ 1 kHz: -80 dB / 10 kHz: -78 dB
(@ 0 dBu, only Line Input)

THD & N: .............................................................. Amplification:

A weighted:

5 dB

-99,4 dBu

20 dB

-97,2 dBu

42 dB

-79,4 dBu

Input Impedance: ............................................. Line: 20 kOhm / Instrument: 1 MOhm

Max. Input Level: ............................................... Line: +22 dBu / Instrument: +14 dBu

Dynamic Response: ........................................ 119 dB

Outputs

Max. Output Level XLR / Jack: ...................... +20 dBu

Output Impedance: ........................................ <50 Ohm

Dimensions

Housing ............................................................... Standard-EIA-19“/2 U

... 482 x 88 x 210 mm

Weight ............................................................... 4,15 kg

Summary of Contents for 9945





























Reviews: