background image

 

INSTALLATION     

 

 

 

 

 

 

 

 

 

 

 
Fixing 
There are 8 fixing screw positions, located as follows. 

(A) – 2 in each side trim of the Grill opening 
(B) – 2 in each side trim of the Oven opening 

Make sure the appliance is fully home in the cabinet/aperture. Open the Oven door and fix 
the screws in position. Finally open the Grill door and fix the screws in position.  
 
Connection  
Gas Connection 
- The gas connection is made to a 10mm compression fitting (Nut and 
olive supplied) on the underside of the appliance. Prior to connection remove the plastic 
protection plug from the fitting. It is recommended that the cooker be connected by copper 
pipe, rubber tubing MUST NOT be used.   
Electrical Connection – Ensure that all electrical cables and wires are routed well clear of 
any heat source, including this appliance. The plug and socket must be accessible after 
installation. 
 

 
 
MAINTENANCE & SERVICING   

 

 

 

 

 

 

 

 

 

This appliance needs little maintenance other than cleaning. All parts should be cleaned 
using warm soapy water. Do not use abrasive cleaners, steel wool or cleansing powders. 
When cleaning the burner ring it is essential to ensure that the holes do not become 
blocked. The control knobs are a push fit and can be removed for cleaning. 
 
ALL SERVICING MUST BE CARRIED OUT BY AN APPROVED COMPETENT PERSON. 
BEFORE ANY SERVICE WORK IS STARTED, THE APPLIANCE SHOULD HAVE BEEN 
LEFT TO COOL AND BE DISCONNECTED AT THE MAINS SOCKET. AFTER EACH 
SERVICE THE APPLIANCE MUST BE CHECKED FOR GAS SOUNDNESS. 
 

1.  Disconnect from gas supply 

Lift and remove the bottom plinth to gain access, then disconnect the gas supply. 

2.  Remove appliance from housing 

Disconnect from gas supply (1). Open the grill door and remove the 2 screws from 
the top of each side trim. Open the oven door and remove the 2 screws from the 
bottom of each side trim. Carefully slide the appliance out one third and check for 
any possible snagging of wires or pipes. If OK, lift appliance out onto a suitable 
surface. 
 

IMPORTANT 

  This appliance MUST be earthed 

 

  After installation the appliance must be tested for soundness 

 

 

The gas supply input pressure to which this appliance is connected MUST not 
rise or fall by more than 2.5mbar from nominal when ALL appliances connected 
to the supply are operated simultaneously. If this appliance is not installed in 
accordance with the instructions and tolerances detailed herein, we the 
manufacturer can not be held responsible for any problems that occur, or poor 
performance that is perceived/witnessed.

 

Summary of Contents for Country Leisure OP96000NG











Reviews: