background image

 

10

MAINTENANCE & SERVICING  

 

 

 

 

 

 

 

 

 
3.  Control replacement  

Disconnect from gas supply (1). Remove appliance from housing (2).  
Grill controls – Remove the locknut from the front of the control panel. Disengage 
the control from the gas rail and remove. 
Oven thermostat - Open the oven door and unscrew the 2 screws holding the 
thermostat probe in position and push the probe back out through the hole in the 
rear of oven. Remove the retaining screws from on top and underneath the control 
and remove from the gas rail. Remove the fittings off the old control and fit on the 
replacement. 

4.  Remove the grill burner 

Disconnect from gas supply (1). Remove appliance from housing (2).  
Release the locking screw on the injector holder. Open the grill compartment door, 
unscrew the locknut on the thermocouple (thermocouple at the rear of the grill 
burner at the left hand side) and push back through the hole in grill hood. Remove 
the spark ignition probe (where fitted) by removing the screw. Lever off starlock 
washers retaining the grill flue. Remove injector bracket fixing screw and lift off flue 
and injector bracket. Lever off starlock washers retaining the grill burner assembly. 

5.  Spark Ignition (where fitted) 

Disconnect from gas supply (1). Remove appliance from housing (2). 
Grill burner - Remove the screw from the bracket and spark ignition probe in the 
top of the burner. Trace the electrode wire back to the generator and pull off the 
connector. 
Oven burner - Trace the electrode wire up the back of the cooker to the generator 
and pull off the connector. Unscrew the fixing screw on the spark electrode inside 
the oven cavity, then carefully pull the electrode from inside the oven and remove. 
Generator – Unplug the generator first. Remove all electrode wires and pull off all 
power and earth wires. The generator is a snap fit into the right side panel; using a 
flat head screwdriver, push in the 2 tabs holding the generator in place and carefully 
remove from panel. 

6.  Grill burner injector (No100) 

Disconnect from gas supply (1). Remove appliance from housing (2). 
Unscrew the locknut on the injector holder at the tube end of the burner, disengage 
the grill pipe from the control and remove the injector. 

7.  Oven burner injector  (No97) 

Open the oven door and unscrew the burner retaining screw, slide the burner to the 
left and lift out. The injector is exposed to the right hand side of the cut out. 
Unscrew the injector. 

8.  Thermocouple replacement  

Disconnect from gas supply (1). Remove appliance from housing (2). 
Grill burner - Unscrew the thermocouple from the control. Unscrew the nut at the 
burner.  
Oven burner - Unscrew the thermocouple from the control. Inside the oven cavity, 
the thermocouple is found just above the burner on the rear wall. Unscrew the 
locknut and pull out the thermocouple from the rear of the appliance. 

9. 

Removing doors 
Grill door -
 Open the grill door halfway and remove the screws on top and bottom 
of the grill door hinges. Carefully lower the grill door and remove. 
Oven door - Open the door and remove the 2 screws retaining the top hinge, tilt the 
door slightly forwards at the top and then lift the door off the bottom hinge.

 

 

 

 

Summary of Contents for Country Leisure OP96000NG











Reviews: