manualshive.com logo in svg

SpierceTech mePed v2, Assembly Manual

Share
Download
SpierceTech mePed v2 Assembly Manual Download Page 2

www.meped.io

2 

mePed v2 Assembly Manual v1.0

WARNING:

CHOKING HAZARD - Small parts.
Not for children under 3 years.

Wood Parts:

 
Before laser cutting the mePed, the wood was covered with a protective masking tape to prevent the wood from becoming 
smoke damaged.  You will need to peel the masking tape off each part before assembling the mePed.  If there is a little bit of 
smoke damage anywhere on the wood after peeling off the masking tape, a light sanding will quickly remove it.

Hardware:

 
Here is a list of fasteners and other hardware included with your new mePed.  The Servo Screws and 
Servo Mount Screws referenced in this assembly manual are included with the servos and do not need 
to be purchased seperately.
 
32ea - M3 Nyloc Nut
28ea - M3 Hex Nut
40ea - M3 x 10mm Screw
16ea - M3 x 12mm Screw
  4ea - M3 x 16mm Screw
  4ea - Nylon Spacer
  1ea - Allen Wrench
  1ea - End Wrench

1ea - Body Top Plate

1ea - Body Bottom Plate

4ea - Leg Parallel Plate

4ea - Leg

4ea - Leg Servo Mount

8ea - Servo Retainer

4ea - Leg Bottom Pivot Plate

4ea - Leg Top Pivot Plate

4ea - Leg Servo Arm

4ea - Leg Parallel Joint

2ea - Battery Tray Spacer

Mini mePed Body

Mini mePed Leg 1

Mini mePed Leg 2

Mini mePed

Retaining Clip

Mini mePed Head

Summary of Contents for mePed v2










Reviews:

No comments

Brands by name

Popular brands

Load more brands