background image

05

SPEX MEDIAL THIGH SUPPORT USER MANUAL

3

WWW.SPEXSEATING.COM

Warning

1.  Spex products shipped out disassembled and with brackets attached loosely. It is the installer’s responsibility to 

ensure all hardware is installed correctly and tightened before using the wheelchair. 

2.  Installation and adjustment of your medial thigh support should be performed only by an authorized dealer or 

qualified therapist. 

3.  Medial thigh support must not be modified or changed as this voids warranty. 

4.  Only use genuine Spex accessories, components and hardware. 

5.  Never lift the wheelchair by the medial thigh support. 

6.  Never use the medial thigh support if any hardware is missing, malfunctioning, or broken. Seek qualified assis-

tance with any repairs, replacements or adjustments. 

7.  A poorly fitted medial thigh support can aggravate posture problems and the overall safety of the user.

8.  The user must not put excessive force against the medial thigh support.

9.  When swinging away the medial thigh support, ensure the user is supported by a carer prior to avoid the user 

falling from the wheelchair. 

10.  Be aware of the pinch points of the swing-away pivot points. Ensure all body parts are kept clear during these 

movements and adjustments.

11.  The locking mechanism must be correctly locking at all times. If it stops locking do not use the equipment. 

12.  A medial thigh support is not a device used to prevent the user sliding forward in the seating.

13.  Never use the medial thigh support without the padding or cover.

14.  Care must be taken when undertaking a user transfer from the seating system. The user may fall from the wheel-

chair or injure themselves when supports are removed.

15.  Never use the medial thigh support without its cover. Care should be exercised near open flame or burning ciga-

rettes. Using the medial thigh support without its cover increases the risk of flammability and skin damage.

Check that the hardware is working correctly, if not you must replace immediately. 
Medifab recommends that all fasteners be checked for wear, such as loose bolts or broken 
components every 6 months. Loose fasteners should be retightened according to the 
installation instructions. Contact your authorized Spex Seating supplier immediately to 
replace any broken components. Do not continue to use the system after identifying 
loose or broken components. The expected lifetime of the Medial Thigh Support is 5 years.

Cleaning the hardware: 

Hardware may be wiped clean with mild detergent and 

water. Dry thoroughly after wiping.

Cleaning the cover: 

Machine wash. Do not bleach. Tumble dry (low heat). Do not iron. 

Do not dry clean. 

If you have any additional questions regarding cleaning procedures, please contact your 
authorized Spex Seating dealer.

Maintenance & Cleaning

Summary of Contents for Pommel









Reviews: