background image

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

802758

2

Washer Dimensions

Before You Start

Supplies 

For most installations, the basic supplies you will need 

are:

Parts Included

An accessories bag has been shipped inside your 

washer. It includes:

Two fill hoses with washers and filter screens. 

Refer to step 2 of 

Installation

.

Four rubber feet. Refer to step 4 of 

Installation

.

Beaded strap. Refer to step 3 of 

Installation

.

Installation Instructions.

User’s Guide.

Warranty Bond.

NOTE: If the washer is delivered on a cold day 

(below freezing), or is stored in an unheated room 

or area during the cold months, do not attempt to 

operate it until the washer has had a chance to 

warm up.

NOTE: Some moisture in the wash drum is normal. 

Water is used during testing at the manufacturer.

NOTE: Install dryer before washer. This allows 

room for attaching exhaust duct.

FLW2224N

Figure 1 

FLW2224N

2 in. (5.1 cm)

26.875 in. (68.3 cm)

28 in. (71.1 cm)

36

 i

n

(91

.44

 c

m

)

31.

1 in.

 (79 cm)

29

.6

 in

(7

5.

1 c

m

)

43

 i

n

(1

09.

2 c

m

)

24 in. (61 cm)

40.

25

 i

n

(10

2

.2

 cm

)

22.38 in.

(56.8 cm)

1

4.

6

 in.

 

(37.

08 cm

)

13.1 in.

(33.3 cm)

1.5 in. (3.8 cm)

FLW2045N

Safety Glasses

2

Wood Block

3

Wrench

4

Screwdriver

5

Pliers

6

Socket Wrench

7

Level

Figure 2 

9/1

6

"

1

2

5

6

4

3

7

Summary of Contents for 802758R4











Reviews: