Spectrum Optio series Owner'S Manual Download Page 6

0190236 Page 6 of 10

Control button

Reset Procedure:

1.  Unplug, then re-plug the power cord into a wall outlet.
2.  Make sure all lift mechanism wire connections are in place and secure.
3.  Remove anything located under the worksurface.
4.  Press and hold the “Down” button to lower the worksurface to the 

lowest “work” position until it stops moving.

5.  Release the “Down” button.
6.  Press and hold the “Down” button again until the worksurface 

bottoms-out, slightly rises, and stops moving.  The worksurface must 

be completely lowered before resuming operation.

Note: If the worksurface does not lower when doing this step, 

release the “Down” button, and retry step 6.

7.  Release the “Down” button.  The lift mechanism has now been 

reset and the worksurface can be adjusted normally.

Down

CAUTION

Always unplug the eLift before working under the worksurface.  

Although this table utilizes an anti-collision feature that briefly stops 

and reverses the motion of the table in the event of an obstruction, 

Use 

caution when raising or lowering the worksurface

!  

Do not 

sit at, 

under, or on the worksurface when operating the lift mechanism and be 

sure table movement does not interfere with objects or people.

Up

CAUTION

Keep clear of pinch points during worksurface movement.

Note: The lift actuators are rated at a maximum capacity of 180 lb each.

CAUTION

USE CAUTION WHEN RAISING OR LOWERING TABLE!

Curved or rectangular 

end worksurface

Control 

button

Phillips 

screwdriver

Tools

 

Required

Operation:

1.  Plug the 11-foot, 15-amp power cord into a wall outlet.

2.  Locate the “Up” and “Down” buttons on the control pad.

3.  To raise or lower the worksurface, press and hold the “up” or “down” 

arrow keys on the control pad until the worksurface reaches the desired 

height.  The worksurface maximum height is 42”, minimum height is 29”.

Keep clear of pinch points during worksurface movement.

#8 x 5/8” PHSM

Pine tree clip

Pine tree clip

Figure 7.2

Note:  Additional sets of pre-

drilled mounting holes are avail-

able under the straight sections 

of the worksurface to mount the 

control button if preferred.

Cord

Figure 7.1

eLift operating instructions - 

eLift equipped tables only

1.  Attach the control button bracket under the radiused portion of the 

worksurface with (2) #8 x 5/8” PHSM screws and pre-drilled pilot holes 

in the center of the worksurface.

2.  Push the control button onto the bracket.

3.  Use the included pine tree clips to secure the cord to the worksurface.

To control box 

in AV channel

Summary of Contents for Optio series











Reviews: