manualshive.com logo in svg

Spectrum Mopit 3.0, Operator'S And Service Manual, Page: 7 / 27

Share
Download
Spectrum Mopit 3.0 Operator'S And Service Manual Download Page 7

 

Page 7 

 

BASIC OPERATION 

Squeegee Lift 

All Mopit 3.0s are 
equipped with a squee-
gee lift. The squeegee 
lift is used for deep 
cleaning. It allows you 
to make multiple 
passes without picking 
up the water on the 
floor. This is called 
double scrubbing. 
When the handle is pointing down, the squeegee is up, and the machine 
is ready to double scrub.  When the handle is pointing up, the squeegee 
is down.  When double scrubbing you may shut off the vacuum to pre-
serve battery life. When you lower the squeegee, turn on the vacuum to 
pick up the water.  
 

Charging The Mopit 

The Mopit is battery operated. It 
should be plugged in whenever it 
is not being used. The on-board 
battery charger is automatic. It 
will turn off when the batteries 
are charged. You do 

not 

need to 

wait until the batteries are fully 
charged to use the Mopit.  You 
do 

not 

 need to run the batteries 

down before you can charge the Mopit.  

Red Light = Charging 
Green Light = Fully Charged 

Scan this QR code with your smart phone to watch how to 
charge the Mopit. You can view all of our Mopit movies on 
the “Mopit Channel” at www.youtube.com. 

Summary of Contents for Mopit 3.0




























Reviews:

No comments