Spectrum 6110FS User Manual Download Page 12 | Manualshive

Page: 12 / 14

Spectrum 6110FS User Manual Download Page 12

12

Com Port
The  gray  software  cable  con-
nects  the  meter  to  the  computer
data port.   Select the Com Port
that  is  assigned  to  the  computer
data  port.    See  Identifying  the
Correct  Com  Port  (p.  9)  for
instructions on how to determine
which port to select.

Meter Type
Select the SC900 option from the
list of available Field Scout me-
ters.

Main Toolbar

Main Toolbar

Main Toolbar

Main Toolbar

17

Measurement

Procedure (Cont.)

depth  measurement  on  the  display  will  increase  in
1-inch  increments.    The  cone  index  will  change  in
response to soil compaction differences.

4. Push probe into ground slowly and evenly so that

there is not any side stress on the shaft.  If an error
message is generated (see Warning  Messages  pg.
18),  start  over  by  removing  probe  and  pushing  the
Start button.

5. Remove probe gently. If the profile was success-

fully measured, the following message will be dis-
played.

6. You can

review compaction measurements

increments  by  pushing  the  Review  button  .    You
can  also  delete  the  profile  by  pushing  the  Delete
button.  See Meter Operation (pg. 6) for details.

7. Press Start to ready the probe for the next

measurement.

Geo-Referencing Compaction Measurements:

To  geo-reference,  you  will  need  to  connect  a  GPS/
DGPS  unit  to  the  SC  900  and  proceed  as  described
above.  The GPS format should be NMEA 0183.  See
Connecting to a GPS Unit (pg.

10) for further details.

Reading Complete

- -Review Mode- -

«
...
10
11
12
13
14
»

Summary of Contents for 6110FS















Reviews:

No comments