background image

0192095 Page 2 of 4

2.  Attach laminate leg panels - optional

2.  Attach laminate leg panels - optional

1.  If you ordered optional laminate leg insert panels, install them into 

the legs at this point with (4) #14 x 3/4” PHSM screws.  

Figure 2

.  

If you don’t have laminate leg panels-skip to step 3.

1.  Assemble worksurface

1.  Assemble worksurface

1.  Place the worksurface laminate side-down onto a non-abrasive 

surface like a carpeted floor.  

Figure 1

.

2.  Install the mid bracket as shown with (1) #14 x 3/4” PHSM screw.

Figure 1

(1) #14 x 3/4” 

PHSM

Worksurface

Mid bracket

Figure 2

Laminate leg 

panel insert

3.  Attach legs to worksurface

3.  Attach legs to worksurface

1.  Attach each leg to the worksurface with (2) #14 x 3/4” PHSM screws.  

Do not tighten screws completely yet.  

Figure 3

.

2.  Install the (4) glides to the bottom of the legs.  The glides can be 

adjusted later to keep the desk level on uneven surfaces.

Figure 3

#14 x 3/4” PHSM

(2 per leg)

(4) Glides

Left Leg

Right Leg

#14 x 3/4” 

PHSM

(2 per leg)

#14 x 3/4” PHSM

(4 required)

Summary of Contents for Esports Meta 37335

Page 1: ... for purchasing Spectrum products Esports Meta Desk 37335 Esports Meta Desk 37335 Esports Shadow Desk 37339 Esports Shadow Desk 37339 1 Worksurface 1 021521 10 24 Keps nut 9 038064 14 x 3 4 PHSM 1 025069 Glide Wrench Hardware 3 8 4 037779 5 16 18 x 1 Glide 6 0100167 8 32 x 1 2 PH Thrd ctg 1 0151223 Left Leg 1 0152137 Cord channel bottom 3 035728 1 4 20 x 1 2 PHMS 3 037542 8 X 5 8 PHSM 0151838 Meta...

Page 2: ...face like a carpeted floor Figure 1 2 Install the mid bracket as shown with 1 14 x 3 4 PHSM screw Figure 1 1 14 x 3 4 PHSM W o r k s u r f a c e Mid bracket Figure 2 Laminate leg panel insert 3 Attach legs to worksurface 3 Attach legs to worksurface 1 Attach each leg to the worksurface with 2 14 x 3 4 PHSM screws Do not tighten screws completely yet Figure 3 2 Install the 4 glides to the bottom of...

Page 3: ...4 20 x 1 2 PHMS 1 Align the cord channel front with the leg holes and mid bracket as shown Figure 4 1 Secure with 2 8 32 x 1 2 PH thread cutting screws and 1 10 24 Keps nut at the mid bracket 2 Align the cord channel bottom and secure to the cord channel front with 3 1 4 20 x 1 2 PHM screws Figure 4 2 3 Secure to each leg with 1 8 32 x 1 2 PH thread cutting screws 8 32 x 1 2 PH Thrd ctg 1 per leg ...

Page 4: ... the left or right side of the desk using 3 8 x 5 8 PHSM screws Figure 7 8 32 x 1 2 PH thrd ctg 2 per leg 8 Flip desk upright 8 Flip desk upright 1 Using two people carefully flip the assembled desk upright Figure 8 3 8 X 5 8 PHSM Support panel Headphone hanger Figure 8 W o r k s u r f a c e CAUTION Do not allow the desk legs to contact the floor until the table is completely flipped over Excessiv...

Reviews: