SpectraPure DWS Instructions Manual Download Page 18

Page: 18 / 18

SpectraPure

SpectraPure®Inc.

480.894.5437 Call us toll-free 1.800.685.2783

2167 East Fifth St, Tempe, Arizona 85281

No. Catalog No.

Optional Part

IMK

Ice Maker Kit

PPRFK-DI

Permeate Pump Retro-Fit Kit used for RO/DI
systems

BPLF-PS-115

Booster pump kit for use with up to 25-60 GPD
system

BPHF-PS-115

Booster pump kit for use with over 60 GPD
systems

FAU-REP

Faucet repair kit

V-PREG-0-125-4GJ

Pressure reducing valve (pressure regulator)

No. Catalog No.

Replacement Parts

Description

SF-MT-1-10

Sediment Filter

1 Micron Sediment Filter (1st Stage)

CF-1-10

Carbon Filter

1 Micron Carbon Pre-Filter (2nd Stage)

MEM (25-90)

RO Membrane

25, 40, 60, or 90 gallon a day Membrane (3rd Stage)

FR (25-90)

Flow Restrictor

25, 40, 60, or 90 gallon a day Flow Restrictor

CF-IN-10

10” in-line post carbon filter Polishes water and removes any taste (4th Stage)

V-ASO-4JG

ASO Valve

Completely shuts off Product water and Waste water

VA-CK-IL-1/2LB-4

Check Valve

Is used in conjunction with the ASO Valve.

REPLACEMENT & OPTIONAL PARTS

Replacement Parts for MPDW

Replacement Parts for DWS & DWS-PP

No. Catalog No.

Replacement Parts

Description

SF-MT-0.5-10

Sediment Filter

0.5 Micron Sediment Filter (1st Stage)

CF-0.5-10

Carbon Filter

0.5 Micron Carbon Pre-Filter (2nd Stage)

MEM (25-90)

RO Membrane

25, 40, 60, or 90 gallon a day Membrane (3rd Stage)

FR (25-90)

Flow Restrictor

25, 40, 60, or 90 gallon a day Flow Restrictor

CF-5.0-10

10” in-line post carbon filter Polishes water and removes any taste (4th Stage)

V-ASO-PP-4JG

Permeate Pump ASO

ASO Valve for Permeate Pump (ONLY FOR DWS-PP)

V-ASO-4JG

ASO Valve

Completely shuts off Product water and Waste water

VA-CK-IL-1/2LB-4

Check Valve

Is used in conjunction with the ASO Valve.

Optional Parts

Summary of Contents for DWS



















Search results

Summary of Contents for DWS

Reviews:

Related manuals for DWS

Brands by name

Popular brands

SpectraPure DWS, Instructions Manual

Search results

Summary of Contents for DWS

Reviews:

Related manuals for DWS

Brands by name

Popular brands