manualshive.com logo in svg

Spectracom 8197, Instruction Manual

Share
Download
Spectracom 8197 Instruction Manual Download Page 75

 

Section 4:  Software Commands 

8197 Instruction Manual 

Page 4-15 

4.2.11   EVENT 

OUTPUT 

 

The Model 8197 maintains logs on alarm conditions, satellite tracking, oscillator 

performance and corrections.  Entries made to these logs are automatically 

output to the RS-232 port they are generated.  The 

Event Output

 command, 

EO

, 

can enable or disable the automatic output of these entries.  The factory default 

is enabled. 

 

To view the Event Output configuration issue the 

EO

 command as follows: 

 

 

 

Type:       

EO<ent>

 

              Response:      

EVENT OUTPUT ENABLED 

 

 

  - 

OR 

- 

 

 

 

     EVENT OUTPUT DISABLED 

 

To enable or disable the 

Event Output

 feature, place the unit in Set Mode and 

issue the following command: 

 

 

 

Type:       

EO ON<ent> 

             Response:       

EVENT OUTPUT ENABLED 

 

 

  - 

OR 

- 

 

 

Type:      

 EO OFF<ent> 

             Response:       

EVENT OUTPUT DISABLED

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for 8197


















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands