Spectra V610 Operation Manual Download Page 5

 

 
 
Compression and Limiting Simultaneously

 

 
Both compression and limiting of audio program material whereby dynamic range can be maximized as well as elimination of audio 
program peaks. 
-The gain reduction, LED meter Vu meter indicates gain reduction. At this input level, the “threshold” LED will be illuminated 
intermittently and not occasionally flicker.  
 
-The amount of compression will be determined by the input level control setting. A visual representation, using the Gain reduction 
LED meter indication should be readily apparent. 
 
-This mode is used whenever a small to intermediate amount of compression is desired. 

 
Compression Only

 

 
When the average level of the input signal to the V610 is continually above the full illumination "threshold" level, then compression 
only occurs. 
 
- Under this mode only “GR”, gain reduction occurs, (under this condition, longer release times are recommended.)   
 

Output Level Control 

 
The V610 utilizes two independent modules/circuits for audio signal compression and gain. 
The compressor limiter function is controlled by the Model 601 Complimiter module. 
 
The output control is a stepped, 24 position detent switch that is calibrated for log operation starting at 2db increments. It is important 
that the user understands the relationship between input level, (gain), and output level, (make up gain). 
 
Improper level adjustment can result in loss of dynamic range and possibly increased system distortion. 
 
The V610 Complimiter has a gain of 65dB. Of the total, approximately 40dB of gain is provided by the second, 110A amplifier 
module. 
 
The sole purpose of the 110A module is to make-up gain for the unit. The output knob of the 610 controls the 110A module gain. If 
the input gain is set at -40dBu as described earlier, then the amount of undistorted gain available is 65dB with 1.1-1 compression. This 
is referenced at+24dBu maximum output, and indicated via the red overload indicator on the M610. Decreases in gain will result as 
compression is increased. 

 
Threshold 

 
A flashing LED indicates transients, (peaks), at -40dBu and below. A constant LED indicates -40dBu and above for program material. 
The threshold circuit operates at high frequencies well beyond conventional peak indicators. As a result, the V610 will indicate peak 
amplitude material without the use of a specialized measurement device. 

 
Overload Input 
 

Complimiter Circuit Input overload  

 
Overload Output 

 
The red overload indicator LED will illuminate whenever excessive input or output signal level overload, (+22 dBu), occurs. In some 
applications it is particularly desirable to utilize the overload indicator LED as a guide to obtaining additional limiting with the output 
of the Model V610 Complimiter 

Summary of Contents for V610
















Reviews: