Specac Silver Gate User Manual Download Page 9 | Manualshive

Page: 9 / 44

Specac Silver Gate User Manual Download Page 9

Silver Gate™ Evolution ATR System

7

3. Installation Via Benchmark™ Baseplate

Figure 1. Silver Gate™ ATR Accessory – Optical Unit with Bridge and

Clamp Anvil Assembly and Flat ATR Crystal Top Plate Assembly

The Silver Gate™ ATR is supported on a Benchmark™ baseplate
when installed into a spectrometer. The Benchmark™ baseplate has
three support pillars (one flat support pillar towards the rear and two at
the front with location pins) and a fourth front central pillar into which
the fixing thumb screw (

1

) of the Silver Gate™ optical unit is tightened.

Note:

It is normally best to install the Benchmark™ baseplate in

the spectrometer first before locating the Silver Gate™ ATR
accessory.

Fixing holes and studs in the Benchmark™ baseplate will vary
dependant on the make and model of the spectrometer for which the
Silver Gate™ is to be installed. For details on how to install your
accessory in the spectrometer, refer to the Benchmark™ baseplate
Installation Guide/User Manual supplied.

1

«
...
7
8
9
10
11
...
»

Summary of Contents for Silver Gate













































Reviews:

No comments