background image

Spearhead Trident 

4000/5000/6000

 

 

 

10

 

Introduction 

 
The  Trident  is  a  very  robust  high  capacity  flail  mower  that  is  easy  to  operate  and 
maintain, to ensure trouble-free operation this manual should be carefully studied.

 

 

Safety First 

 

Do  not  start  the  machine  until  you  fully  understand  the  operation  and  safety 
precaution  requirements.    Always  ensure  the  operators  are  proficient  with  the 
operation of this type of machine. 
 

Tractor Requirements

 

 

 

Spearhead recommended 70 

– 90HP tractor for the Trident 4000 

 

       80 

– 110HP tractor for the Trident 5000 

       110 

– 150HP tractor for the Trident 6000

 

 

 

Fixed  clevis  drawbar  minimum  height  (17”)  430mm,  at  maximum  extension 
(14”) 355mm.

 

 

 

Minimum tractor weight 3000kg including ballast.

 

 

 

PTO  must  be  independent  live  drive  to  enable  continuous  PTO  drive  even 
when tractor clutch is pressed down.

 

 

 

External oil supply (min. pressure 140 bar) and free flow returns.

 

 

 

CAT 2 front or rear linkage.

 

 

 

Attaching to the Tractor – Trailed Machine 

 
It is advisable to remove the tractor rear link arms.  However, if this is not convenient, 
at least check the link arms do not contact the PTO shaft when turning. 
 
Before coupling to the tractor, it is important to check that the tractor draw bar is out 
at  its  longest  setting,  which  will  give  the  tightest  turning  circle  without  risk  of 
bottoming the PTO shaft. 
 
 

                                                                                            
 
 
 
 
 
 
 
 
 

When fitting the pin through the drawbar clevis, 
insert the plastic washer between the tractor and 
machine drawbar as shown.  This washer is a 
replaceable wearing part. 

 

   

Do not attach the machine to the 
pick-up hook as this will result in 
serious damage to the PTO 

Summary of Contents for Trident 4000


























Reviews: