These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, micro
fi
lming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in technology and equipment reserved.
© Copyright 2012 by Conrad Electronic SE.
Version 11/12
TV wall bracket 81-152 cm (32-60”)
fully portable
Item no. 98 99 30
Preparation of the TV set
• Normally, one must remove the stand of the TV set before mounting. Observe the operating instructions for your TV
set.
• Place the TV set
fl
atly, with the display side facing downwards on a point and clean base. Do not exert any pressure
on the display. Protect valuable furniture surfaces during installation by using a suitable pad or cloth.
• Remove the present stand. It is screwed tightly or clipped, depending on the TV set
Figure 2
•
De
fi
ne the position and height of the wall bracket at the installation location. The integrated spirit level must point
towards the left.
• Make the wall bracket horizontal with the help of the spirit level.
• Mark the necessary drilling holes on the installation surface. Use the wall bracket as a stencil for this.
• Drill the required holes and provide the holes with suitable dowels.
• Fix the wall bracket with suitable screws and
fl
at washers, as shown in the
fi
gure.
Figure 3
There are different installation possibilities, depending on the position of the mounting points on the TV rear side.
VESA 100x100 bis 200x200
• As shown in the
fi
rst
fi
gure, the installation plate can be installed directly on the rear side of your TV set.
VESA up to 400x400
• As shown in the second
fi
gure, the installation plate is installed with the attached longitudinal and cross beams on
the rear side of your TV set.
• Use the M8x14 black hexagonal socket screws from the attached set of screws to fasten the longitudinal and cross
beams.
The installation plate must be brought to the centre of the TV set without fail.
Figure 4
• Fasten the installation plate with
fi
tting screws (F-1) and
fl
at washers on the rear side of your TV set as shown in the
fi
rst or second
fi
gure.
• During installation, ensure that the arrow on the installation plate points towards the top side of the TV set.
When
fi
xing the installation plate, ensure without fail that the correct screws are used. These must
not only have threads that match the TV set, they should also not be too long, as otherwise the TV
set may be damaged.
However, the screws must not be too short, as otherwise the connection will not be secure. They
must be screwed into the corresponding threads of the TV set with at least 5 full 360° turns.
If the length of the screws in the attached screw set is not suitable for your TV set, please procure
fi
tting screws from the local hardware shop.
If you have any doubt about the correct length of the screws, please contact the TV manufacturer
or an appropriate specialist.
• Do not use force when tightening the screws; otherwise the TV set may be destroyed, leading to loss of warranty/
guarantee!
• If your TV set has an arched rear side or the distance from the wall must be increased for some other reason, you
can use the plastic spacers (N or O) from the screw set between the TV set and the installation plate. In this instal-
lation type, the longer screws (J-M) from the screw set are used.
Figure 5
• Lift the TV set with the installation plate as shown in the
fi
rst
fi
gure from the top of the wall bracket.
• The two
fl
aps of the installation plate must be inserted into the recesses of the wall bracket.
• Secure the installation plate on the wall bracket with the M6x36 black cross-head screws. Tighten the screws until
it is impossible to remove the TV set from the bracket.
• Then adjust the desired inclination angle as shown in the second
fi
gure with the two lever screw joints. The lever on
the screws can be pulled out to use the lever like a ratchet.
Maintenance and Care
The product does not have to be serviced and, except for occasional cleaning with a soft, dry cloth, requires no
maintenance whatsoever.
Never use aggressive cleaning agents or chemical solutions as these may damage the surface of the case.
Technical Data
TV size .............................................81-152 cm (32-60“)
Load capacity ..................................max. 55 kg
VESA mount ....................................max. 400 x 400
Material ............................................steel
O P E R A T I N G I N S T R U C T I O N S
Intended use
The TV wall bracket is used to install suitable TV sets on walls.
The TV set should not exceed the TV size and weight values speci
fi
ed in “Technical Data”.
Any use other than the one described earlier can lead to this product or the TV set being damaged. It is also exposed
to dangers such as damage to furniture in the vicinity of the wall bracket, physical injury to persons etc.
No part of the product may be modi
fi
ed or altered.
The safety instructions must be observed at all times.
Package Contents
See Figure 1 on the sheet attached to this manual.
Safety Instructions
The warranty will be void in the event of damage caused by failure to observe these safety
instructions! We will not assume liability for any resulting damage.
We shall not accept liability for damage to property or personal injury caused by incorrect han-
dling or non-compliance with the safety instructions. In such cases, the warranty will be null and
void.
The exclamation mark symbol indicates important information in these operating instructions.
The arrow symbol indicates tips and instructions
• A TV set bracket is not a toy Keep the device out of the reach of children.
• Do not leave packaging material lying around carelessly. They may become dangerous playthings for children.
• Selecting an unsuitable installation location can lead to personal or material damage.
• Proceed with care when assembling or installing the product. The product can have sharp edges. There is risk of
injury!
• Only carry out the work on the TV wall bracket that is necessary for its installation (setting). Never attempt alterations
or repairs.
• Before beginning the installation process, check whether there are appropriate mounting options for a TV set on the
rear of your TV wall bracket.
•
Depending on the size and design of the TV set and TV wall bracket, a second person should assist with with the instal-
lation. They can for example, hold the TV set when you mount it on the wall bracket.
• Apply your full concentration when carrying out the installation, because if the TV set and/or TV wall bracket were
to fall, this could cause expensive consequential damage to the equipment. There is also the potential danger of
personal injury!
• Route all the TV set’s cables in such a way that they do not get jammed or kinked in the TV wall bracket.
• Check all the screw joints from time to time. Adjusting the position of the TV set and/or the TV wall bracket and
moving them can sometimes cause the screws to become loose over time.
• Do not use force while moving or adjusting the TV set or TV wall bracket. The TV set could get damaged.
• When moving/adjusting, do not press on the screen of the TV set.
• Do not overload the TV wall bracket. Pay attention to the details provided by the manufacturer for the maximum TV
set weight and/orsize.
• Do not use the TV wall bracket to support yourself or hold on to it.
• Do not mount any object on the TV wall bracket other than the TV set intended for it.
• In case of uncertainty, do not perform the installation on your own. Leave this work to a technician.
Installation
Wall-mounting is permissible only if the quality of the wall is suitable for such installation. Light-
weight partition walls or those made from gypsum boards are normally unsuitable. However,
specialist retailers do sometimes stock special dowel
fi
ttings for such installation locations. If
you are in doubt, ask a specialist before installation.
Depending on the base (e.g. concrete), suitable mounting materials must be used (screws, dow-
els, etc.). The attached dowels are suitable exclusively for solid walls. Special dowels and screws
are not attached to the TV wall bracket, and must be purchased separately, depending on the
quality of the wall.
A stable mounting must be ensured due to the weight of the TV set, TV wall bracket and the lever
action.
Plan the installation location carefully so that the TV wall bracket containing the TV set is in the
desired position after the installation (height and position).
Pay attention when drilling and tightening the screws that no cable or pipes in the wall are dam-
aged. Inadvertently drilling through electric cables causes the life-threatening danger of an elec-
tric shock!
Pay special attention to your safety when using electric tools (e.g. a drill). You should heed the
safety instructions in the corresponding manuals.
Ensure that there is no person in the area under the TV wall bracket or TV set.
Please follow the
fi
gures in the sheet attached to this manual.
