G
O P E R AT I N G I N T R U C T I O N S
1080p HDMI radio transmission
Item no. 1365375
Intended use
This product enables the wireless transmission of HDMI-compatible digital AV signals via radio from a play-
back device (e.g., satellite receiver) to a receiver (e.g., television/monitor).
Radio transmission of the IR control signal from an IR remote control is also possible, so the location of the
playback device can be chosen freely.
The voltage/power is supplied via two enclosed wall plug transformers.
Always observe the safety instructions and all other information included in these operating instructions.
This product complies with the applicable national and European requirements. All names of companies and
products are the trademarks of the respective owners. All rights reserved.
HDMI is a registered trademark of HDMI Licensing L.L.C.
Package contents
• Transmitter module (label “TRANSMITTER”)
• Receiver module (label “RECEIVER “)
• 2 Wall plug transformers
• IR transmitter (for connection to the transmitter module)
• IR receiver (for connection to the receiver module)
• Operating instructions
Safety instructions
The warranty will be void in the event of damage caused by failure to observe these safety
instructions! We do not assume any liability for any resulting damage!
We do not assume any liability for material and personal damage caused by improper use
or non-compliance with the safety instructions! In such cases, the warranty will be null
and void.
a) General
• Unauthorised conversion and/or modification of the product is not allowed for safety and approval reasons
(CE). Do not disassemble the product.
• Any maintenance or repair work may only be performed only an expert.
• Do not carelessly leave the packaging material lying around, since it could become a dangerous plaything
for children.
b) Wall plug transformers
• The design of both wall plug transformers enclosed complies with Protection Class II. Use only a standard
mains socket as the power source for the wall plug transformers.
• The mains socket into which the mains plug is plugged must be easily accessible.
• Only use the two provided wall plug transformers to power the product.
• Do not disconnect the wall plug transformers from the mains socket by pulling the cable. Take hold of it on
the sides of the housing and pull it out of the mains socket.
• If a wall plug transformer is damaged, do not touch it; there is danger to life from electric shock!
First, switch off the mains voltage to the socket to which the wall plug transformer is connected (switch
off at the corresponding circuit breaker or remove the safety fuse or switch off at the corresponding RCD
protective switch, so that all poles of the mains socket are disconnected).
You can then unplug the power adapter from the mains socket. Dispose of the faulty power adapter in an
environmentally friendly way, do not use it any more. Replace it with a power adapter of the same design.
c) Operation
• The product is not a toy. Devices operated on mains voltage should not be used by children. Therefore, be
especially careful when children are around.
Use the product where it is out of the reach of children.
• The product is intended for use only in dry, indoor locations. No part of the product should become damp
or wet; never handle it if your hands are wet!
With the wall plug transformers there is also the deadly peril of an electric shock!
• Avoid the following adverse conditions at the location of installation and during transport:
- Dampness or excessive humidity
- Extreme cold or heat, direct sunlight
- Dust or flammable gases, fumes or solvents
- Strong vibrations, impacts or blows
- Strong magnetic fields such as those found in the vicinity of machinery or loudspeakers
Version 08/15
• Do not place objects on the product; never cover the product.
• Never use the product immediately after moving it from a cold room into a warm one. The condensation
that forms might damage the product. With the wall plug transformers there is also the deadly peril of an
electric shock!
Allow the product to reach room temperature before connecting it to the power supply and putting it into
use. This may potentially take several hours.
• When setting up the product, make sure that the cables are neither kinked nor pinched.
• Handle the product with care; it can be damaged by impacts, blows or falls even from a low height.
Controls and connections
A) Transmitter module (“TRANSMITTER”)
1 Micro-USB socket for power supply
2 “IR OUT” socket for IR transmitter
3 HDMI output (“HDMI OUT”) for looping the HDMI signal through
4 HDMI input (“HDMI IN”)
5 “MODE” button
6 Power LED
B) Receiver module (“RECEIVER”)
7 Micro-USB socket for power supply
8 “IR IN” socket for IR receiver
9 HDMI output (“HDMI OUT”)
10 “MODE” button
11 Power LED
Connection
Example:
First switch off all the devices that you wish to connect with the transmitter and receiver modules.
Using the enclosed IR transmitter and IR receiver it is possible to transmit IR signals via radio from transmit-
ter module (“TRANSMITTER”) to the receiver module (“RECEIVER”).
In this way, you can continue to use the playback device’s (e.g., satellite receiver) IR remote control, even
though the playback device is not in the detection range of the IR remote control!
a) Transmitter module (“TRANSMITTER”)
• Connect the HDMI input “HDMI-IN” (4) on the transmitter module to the HDMI output on a playback device,
e.g., HDMI output from a Blu-ray player or a game console.
• A TV set/Monitor can be connected to the HDMI output “HDMI OUT” (3). The HDMI signal at the HDMI
input “HDMI IN” (4) is looped through here.
1 2
3
4
7 8
9
5
10
6
11
