manualshive.com logo in svg

SPE BEF320-3A, Operating Manual

Share
Download
SPE BEF320-3A Operating Manual Download Page 10

 
 

ACCESSORIES 

 

 

Part number 

Description 

Application 

 

32001

 

Heavy duty drum complete with 

T.C.T. cutters and spacers.

 

Hardened steel cutter with 

tungsten inserts, for all concrete 

texturing, scabbling, planing and 

grooving applications. Removal of 

bridge deck and car park 

membranes, heavy industrial 

contamination, epoxy coatings and 

road markings. Use on heavy 

applications for longer life and 

higher output.

 

32002

 

Heavy duty drum complete with 

beam flails

 

Heat treated steel cutter for the 

removal of paint coatings and 
laitence from new floors. Also 

used for removing of grease build 

ups, dirt and ice deposits, keying 

and light scabbling of concrete 

when a "fine textured" surface is 

required.

 

32003

 

Heavy duty drum complete with 

milling cutters and spacers.

 

For the removal of thermoplastic 

road/runway markings. Very 

efficient and cost effective with 

none of the problems associated 

with burning off thermoplastics. 

Also for removal of bituminous 
materials and rubber deposits.

 

80800

 

T.C.T. Cutter: 8 point hardened 

steel cutter with tungsten carbide 

insert.

 

For all concrete texturing 

scabbling, planing and grooving 

applications. Removal of bridge 

deck and car park membranes, 
heavy industrial contamination, 

epoxy coatings and road 

markings. Use on heavy 

applications for longer life and 

higher output.

 

80120

 

 

   Beam cutter: Heat treated steel     
cutter.

 

For the removal of paint coatings 

and laitence from new floors. Also 

used for the removing of grease 

build ups, dirt and ice deposits, 

keying and light scabbling of 

concrete when a "fine textured" 

surface is required.

 

 
 

 

 

7 

Summary of Contents for BEF320-3A















Reviews:

No comments

Brands by name

Popular brands

Load more brands