LIGHT BUTTONS
(
) LIGHT ON / MODE BUTTON
ON
OFF
UP
DOWN
(
) LIGHT SPEED / COLOUR
UP
DOWN
OK
[L.BRT] LIGHT BRIGHTNESS
UP
DOWN
Two light buttons are used to control the many
features of the multi colour LED spa light.
Press to toggle light
and
. The button is
backlit green to indicate when the light has been
turned ON.
When the light is first turned on the light mode menu
will be displayed. The current light mode in use will be
shown. Use the
(
) or
(
) button to
step through the five colour modes:
(1) White
[WHTE]
(2) User Colour [U.CLR]
(3) Fade Effect
[FADE]
(4) Step Effect
[STEP]
(5) Party Effect [PRTY]
Press to activate the light speed [L.SPD] or user
colour [CL:xx] adjustment screens. If FADE / STEP or
PARTY effect modes are selected the current light
speed [L.SPD] will be displayed. If the user colour
[U.CLR] light mode is selected the current colour
number will be displayed (refer below).
Press the
(
) or
(
) button to adjust
the light effect transition speed OR select from 30
colour choices. Press
(
) to confirm selection
or wait for the 10 second idle menu timeout where the
screen steps to the light brightness [L.BRT] screen.
When the [L.BRT] adjustment screen is displayed
press the
(
) or
(
) button to adjust
the light brightness.
Note: If White [WHTE] colour mode is selected the Light
Speed/Colour button has NO function.
ERROR CODES / DIAGNOSTICS
Note: most error conditions require mains power to be turned
and back
before the error is cleared.
Check the
"Heater" sensor lead is plugged firmly into the spa control.
Press
Pump A button to retry water prime. Check spa water level, clean
and soak filters, bleed potential air locks from pipework.
Check spa water level, clean & soak filters, check
all shut-off valves are open, bleed potential air locks from pipework.
Remove spa cover & allow
spa to cool. Check daily filtration time & reduce setting if required.
Turn mains power OFF and unplug and
reconnect "Heater" sensor lead from spa control.
Contact your local dealer. Disconnect "In Pool Sensor" lead
from spa control to continue spa operation.
Reset mains power. Contact your local dealer if problem persists.
OFF
ON
ER2 - HEATER PLUG:
ER3 - WATER PRIME:
ER4 - THERMAL TRIP:
ER5 - POOL TOO HOT:
ER6 - HEATER SENSOR:
ER7 - IN POOL SENSOR:
ER8 - CTRL FAULT:
Heater sensor cable fault.
Heater tube failed to fill with water.
Low or NO water flow over element whilst
heating has activated thermal cut-out device on heater. Turn mains
power OFF and wait 20~30 minutes for heater to cool and thermal
cut-out to reset.
Temperature sensor has reported a
temperature reading in excess of 45 C.
Communication between spa control
and heater has been lost.
In Pool Temperature Sensor has
faulted.
An internal controller fault has been detected.
o
PUMP BUTTONS
ON / OFF / LOW / HIGH / AUTO
There are four pump buttons on the right hand side
of the touch pad: Pump A, Pump B, Pump C and
Pump D. The functions of the four buttons change
depending on pump / controller configuration.
The intention is to make best possible use of these
buttons for all possible configurations. For every press
of a pump button, the display will temporarily show the
selected pump state:
then revert to the default display mode. Possible pump configurations & button sequences are referenced in the
table below (Please tick your spa configuration for ease of future reference).
Notes:
1) If left ON pumps will automatically time-out and turn off 30 minutes after the last sensed button press.
2) In some configurations if heater is ON activating multiple pumps OR turning the blower ON may cause the spa control to
load shed and turn the heater OFF. This is to keep the system within its maximum power load.
RAMPING BLOWER MODE
The spa controller features a ramping blower mode,
were the blower speed gradually fluctuates between
high and low in a ramping manner.
To turn the blower on in ramping mode:
To activate a 20 minute water clean-up cycle:
1) Press the
(
) button
to start
the blower in ramping mode.
2) Press the
(
) button again to turn
the blower OFF.
A sanitise cycle runs the filtration pump and ozone /
uv (if fitted) to filter the spa water to restore and
refresh water quality after use. In addition, at the
start and end of the cycle, the controller will
sequentially run any additional pumps and the
blower (if fitted) for one minute each to purge the
plumbing and clear any unfiltered water trapped in
those lines.
1) Press the
(
) button once after spa
use to activate the water clean [W.CLN] cycle.
BLOWER
BLOWER
ONE-TOUCH SANITISE BUTTON
SANITISE
INVERT BUTTON
twice
The blower will turn
ON and the screen will display [RAMP] to indicate
ramping mode.
Note:
SANITISE
If cycle running, cycle can be cancelled by
pressing the
button again.
Press the
(
) button to flip the screen
180 for ease of viewing when spa in use. The
(
) and
(
) button functions also
change (invert) to match the new display.
INVERT
UP
DOWN
o
AIR BLOWER BUTTON
BLOWER
UP
DOWN
OK
BLOWER
The BLOWER (
) button is used to control the air
blower and allow adjustment of the blower speed.
The last used speed is saved and will be restored the
next time the blower is turned on, for future ON/OFF
use.
1) Press the
(
) button
to turn
the blower ON in variable speed mode.
2) The blower will turn ON (at the last used speed)
and the screen will display the blower speed
[B.SPD] adjustment screen (refer below).
3) Use the
(
) or
(
) buttons to
adjust the blower speed.
4) Press the
(
) button to confirm selection.
5) Press the
(
) button again to turn
the blower OFF.
Note: that when the blower is first turned on it will run
at maximum speed for approx three seconds before
changing to your preset speed; this is normal.
Note: The B.SPD adjustment screen is displayed for 10
seconds when the blower is first turned ON. If no
adjustment is made the blower will run at the last used
speed setting, and the screen will time-out and revert to the
default display mode. If you wish to adjust the blower speed
once the blower has been running for a period of time, the
blower must be turned OFF and back ON again to restore
the B.SPD adjustment screen.
To turn the blower on/off:
once
Note: the bar graph will
change indicating current blower speed.
OK
OK
°C
°F
MODE
SPD
BRT
SPD
OFF
ON
6.SPD
Bargraph indicates blower speed
I
AM
PM
OFF
ON
°C
°F
MODE
SPD
BRT
SAT SUN MON TUE WED THU FRI
L.SPD
AM
PM
OFF
ON
°C
°F
MODE
SPD
BRT
MODE
SPD
BRT
SAT SUN MON TUE WED THU FRI
CL:01
Light speed screen
User colour screen
SPD/
CLR
I
I
I
I
OK
Pump Button
Pump Button
Pump Button
Pump Button
A
B
C
D
Spa Configuration
Button A
Button B
Button C
Button D
No small circ pump
P1, P2 & P3 = 1 speed
Jet pump 1:
On / Off / Auto
Jet pump 2:
On / Off
Jet pump 3:
On / Off
No Function
No small circ pump
P1, P2, P3 & P4 = 1 speed
Jet pump 1:
On / Off / Auto
Jet pump 2:
On / Off
Jet pump 3:
On / Off
Jet pump 4:
On / Off
No small circ pump
P1 = 2 spd, P2 & P3 = 1 spd
Jet pump 1:
Low / Off / Auto
Jet pump 1:
High / Low
Jet pump 2:
On / Off
Jet pump 3:
On / Off
No small circ pump
P1 = 2 speed, P2 = 2 speed
Jet pump 1:
Low / Off / Auto
Jet pump 1:
High / Low
Jet pump 2:
Low / Off
Jet pump 2:
High / Low
Small circ pump fitted
P1, P2 & P3 = 1 speed
Small circ pump:
On / Off / Auto
Jet pump 1:
On / Off
Jet pump 2:
On / Off
Jet pump 3:
On / Off
Small circ pump fitted
P1, P2, P3 & P4 = 1 speed
Jet pump 1:
On / Off
Jet pump 2:
On / Off
Jet pump 3:
On / Off
Jet pump 4:
On / Off
Small circ pump fitted
P1 = 2 spd, P1 = 1 spd
Small circ pump:
On / Off / Auto
Jet pump 1:
Low / Off
Jet pump 1:
High / Low
Jet pump 2:
On / Off
Small circ pump fitted
P1 = 2 spd, P2 & P3 = 1 spd
Small circ pump:
On / Off / Auto
Jet pump 1:
Low / High / Off
Jet pump 2:
On / Off
Jet pump 3:
On / Off
Small circ pump fitted
P1 = 2 speed, P2 = 2 speed
Small circ pump:
On / Off / Auto
Jet pump 1:
Low / High / Off
Jet pump 2:
Low / High / Off
No Function
