QUICK REFERENCE GUIDE
CHANGING LIGHT MODES
PARTIAL KEYLOCK
[FILT]
DAILY FILTRATION TIME
OFF
P.SAV disabled
LOW
Filtration only
Press Light (mode) button to
Press and hold this button combination
This setting is used to control the hours
HIGH
Filtration and heating
until LOCK appears on the display:
of filtration per day. Filtration limits
display current light mode in use.
differ depending on pump type.
Once P.SAV mode is selected the begin
and end times of the PEAK power tariffs
Press or button to step
Circ Pump
(2A or less)
1-24 hrs
must be set so the control knows NOT
through choice of light modes:
Repeat button combination to unlock.
Jet Pump
(2spd or 1spd)
1-8 hrs
to operate during those hours.
WHTE
White Light
Note:
Once locked only pumps, blower,
BGN
Peak power begin time
UCLR
User Colour
light and sanitise buttons can be used.
[F.CYC] FILTRATION CYCLES
END
Peak power end time
FADE
Fade Effect
Access to all other buttons is disabled.
STEP
Step Effect
This setting defines how often filtration
PRTY
Party Effect
cycles occur. Filtration can be set to run
[W.CLN] AUTOMATIC SANITISE
SETUP MENU
every 1/2/3/4/6/8/12 or 24 hrs
CHANGING LIGHT SPEED OR
This setting allows adjustment of the
LIGHT COLOUR
The setup menu allows customisation
start time of the 10 minute automatic
of the adjustable controller settings.
[SNZE] SLEEP TIMERS
daily sanitise cycle. Setting can be
Dependant on light mode selected the
Menu access and item adjustments are
adjusted from 0:00 to 23:59.
Light (spd/clr) button will activate
carried out as follows:
Used to disable automatic heating and
one of three light mode option screens.
filtration during certain times of day or
Press and hold and buttons
night. Upon entering SNZE menu there
[D.DIS] DEFAULT DISPLAY MODE
CL:xx
User Colour Number
are four choices:
together until [MODE] is displayed.
L.SPD
Light Transition Speed
Used to adjust the default display mode
L.BRT
Light Brightness
1.SNZ
Sleep Timer #1
shown on the keypad. Setting choices:
Press or to navigate through
2.SNZ
Sleep Timer #2
Press or button to adjust
R.SET
Reset timers to default
setup menu items.
W.TMP
Water Temperature
EXIT
Exit sleep timer menu
each setting.
S.TMP
Set Temperature
TIME
Clock
Press to enter item adjustment.
Only one sleep timer needs to be set
Press button to save each setting
however two timers are provided to
and move to the next setting.
Press or to adjust setting.
facilitate different sleep settings on
[T.OUT] LOAD TIME OUTS
different days. Each sleep timer setting
Note:
All light settings are saved for
consists of a week day setting, start
Press to confirm setting and exit.
All accessory loads (ie. pumps and/or
future ON / OFF use.
time and stop time (refer below).
blower) automatically turn off after a
All setup menu items follow the same
x.DAY
Day(s) of operation
time out period has elapsed. Fifteen
adjustment procedure. Menu items that
x.BGN
Sleep timer begin time
(15) minutes later the lights will switch
FULL KEYLOCK
can be adjusted are as follows:
x.END
Sleep timer end time
off and the pool will return to automatic
mode. This setting allows the length of
Press and hold this button combination
Use the Up, Down & OK buttons to
the time out period to be adjusted.
until LOCK appears on the display:
[MODE] OPERATING MODES
adjust and confirm each setting.
Setting ranges from: 10 - 60 minutes
Operating modes effect demand
heating and filtration behaviour. The
[P.SAV] POWER SAVE (off peak)
setting choices are:
Repeat button combination to unlock.
Reduce operating costs by limiting
NORM
Normal heating & filtration
Note:
Once locked if any button is
filtration and heating to occur only
ECON
Heating only during filtration
pressed the key stroke will be ignored
during cheaper off peak power periods.
AWAY
Heating disabled. Filtration
and the display will show LOCK.
There are three P.SAV modes:
reduced to 1hr p/day
up
down
pump
a
+
+
up
down
pump
b
+
+
MODE
SPD/CLR
