background image

2

ID#   M316001

01/07

SAFETY INSTRUCTIONS

• This equipment is intended for home recreational use only

and NOT excessive competitive play. 

• Read and understand the warning label enclosed with

hardware.  It is the responsibility of the customer to mount
this label.  It should be affixed to the pole, wall, or door
near playing area, at a height between 4-6 feet (1.2 -1.8 m)
above ground level and in a location visible to all players. 

• If using a ladder during assembly, use extreme caution.
• Two (2) capable adults are recommended for this

operation.

• If technical assistance is required, contact Customer

Service. 

• Adult supervision is recommended when adjusting height. 

FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY
RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND

WILL VOID WARRANTY.

Owner must ensure that all players know and follow these rules

for safe operation of the system.

To ensure safety, do not attempt to assemble this system without
following the instructions carefully. Proper and complete
assembly, use and supervision is essential for proper operation
and to reduce the risk of accident or injury. A high probability of
serious injury exists if this system is not installed, maintained,
and operated properly. Check entire box and inside all packing
material for parts and/or additional instructional material.  Before
beginning assembly, read the instructions and identify parts
using the hardware identifier and parts list in this document.

Most Injuries are caused by misuse and/or not following instructions.

Use caution when using this unit.

Owner must ensure that all players know and follow these rules 

for safe operation of the system.

WARNING

•  DO NOT HANG on the rim or any part of the system including 

backboard, support braces or net.

•  During play, especially when performing dunk type activities, 

keep player's face away from the backboard, rim and net. 
Serious injury could occur if teeth/face come in contact with 
backboard, rim or net.

•  Do not slide, climb, shake or play on base and/or pole.
•  When adjusting height or moving system, keep hands and 

fingers away from moving parts.

•  Do not allow children to move or adjust system.
•  During play, do not wear jewelry (rings, watches, necklaces, 

etc.). Objects may entangle in net.

•  Keep organic material away from pole base. Grass, litter, etc. 

could cause corrosion and/or deterioration.

•  Check pole system for signs of corrosion (rust, pitting, 

chipping) and repaint with exterior enamel paint. If rust has 
penetrated through the steel anywhere, replace pole 
immediately.

•  Check system before each use for proper ballast, loose 

hardware, excessive wear and signs corrosion and repair 
before use.

•  Check system before each use for instability.
•  Never play on damaged equipment.
•  Keep pole top covered with cap at all times.
•  See instruction manual for proper installation and 

maintenance.

R

ead

 

and

 

understand

 

warnings

 

listed

 

below

 

before

 

using

 

this

 

product

.

F

ailure

 

to

 

follow

 

these

 

warnings

 

may

 

result

 

in

 

serious

 

injury

 

and

/

or

 

property

 

damage

.

ID#: 588000    05/05

In the U.S.: 1-888-713-5488

In the U.S.: 1-800-558-5234
In Canada: 1-800-284-8339

In the U.S.: 1-800-334-9111

In the U.S.: 1-800-558-5234
In Canada: 1-800-284-8339

After installation is

complete, adhere this

WARNING label (7) in

a clearly visible

place.

NOTE:

Crank

Hook

HEIGHT ADJUSTMENT

TO ADJUST BACKBOARD:

Position looped end of 

crank onto hook as shown.

Rotate crank handle to 

raise or lower backboard 

509000

1/07

33

7

Summary of Contents for M316001
















Reviews: