manualshive.com logo in svg

Spaceman SM-6650, Machine Manual, Page: 19 / 24

Share
Download
Spaceman SM-6650 Machine Manual Download Page 19

www.spacemanusa.com 

Phone: (720) 328-1020 

Email: [email protected] 

Problem: Product won’t dispense 

Problem: Product leaks excessively 
into internal drip tray 

Problem: Scored Cylinder walls 

Problem: Product leaks excessively 
from dispensing door spout 

Probable Cause 

1.  Product is over-frozen in cylinder 

2.  Inadequate mix in hopper 

3.  Power switch is in the OFF position 

4.  Unit is unplugged 

5.  Tripped circuit breaker or blown fuse 

6.  Improper mixing of product 

7.  Machine has tripped safety reset 

8.  Beater assembly is rotating counter-clockwise 

or is not rotating 

Remedy 

1.  Lower viscosity setting as required (Page 16) 

2.  Ensure hopper is at least half full 

3.  Turn power switch to FREEZE 

4.  Verify machine is plugged into power source 

5.  Verify and reset circuit breaker and/or fuse 

6.  Follow manufacturer instructions for mixing 

product; ensure correct mix ratios 

7.  Reset machine (Page 15) 

8.  Contact Spaceman USA Technical Support 

Probable Cause 

1.  Improper or inadequate lubrication of drive 

shaft gasket 

2.  Damaged, missing, or improperly installed 

drive shaft gasket 

Remedy 

1.  Use sufficient food-grade lubricant, and add 

sufficient lubricant inside drive shaft gasket 
during assembly (Page 11) 

2.  Replace drive shaft gasket every 1 to 3 

months; replace torque assembly  guide every 
1 to 3 months 

Probable Cause 

1.  Improper or inadequate lubrication of draw 

valve and draw valve O-rings. 

2.  Cracked, broken, or worn draw valve O-rings 

Remedy 

1.  Use sufficient food-grade lubricant when 

assembling draw valve (Page 12) 

2.  Replace O-rings every 1 to 3 months 

Probable Cause 

1.  Broken torque or beater assembly 

2.  Beater guide worn or missing 

Remedy 

1.  Repair or replace torque or beater 

assembly 

2.  Replace or install beater guide 

Problem: Machine Shuts down 
Automatically 

Probable Cause 

1.  Cylinders are experiencing freeze-up (usually due 

to viscosity being set too high for selected 
product) 

Remedy 

1.  Reset machine (Page 15), and lower viscosity as 

required (Page 16) 

 

Troubleshooting 

18 

Summary of Contents for SM-6650

























Reviews:

No comments