background image

 

Technical data 

 

Work Light Specs 

Burn Time Main Light 

 

1.5 hours on hi approx.. 

Burn Time Spot Light 

10 hours approx.. 

Light Source 

5w SMD LED 

Main Light Power  

Max 500 lm Min 75lm 

Spot Light Power Max 

150lumens 

Charging Time 

4.5hours 

Battery Type 

Lithium-ion 

Battery Capacity 

3.7v/2600mA 

Input Voltage to Charge Pad  

USB 5v/1000mA 

Splash Water Protection 

IP65 

Operating Temperature 

-10°C -+40°C 

 

 

 

Pocket Light Specs 

Burn Time Main Light 

 

2hours on hi approx. 

Burn Time Spot Light 

5hours approx. 

Light Source 

3w SMD LED 

Main Light Power  

Max 300 lm Min 30lm 

Spot Light Power Max 

100lumens 

Charging Time 

2.5hours 

Battery Type 

Lithium-ion 

Battery Capacity 

3.7v/1200mA 

Input Voltage to Charge Pad   USB 5v/1000mA 

Splash Water Protection 

IP65 

Operating Temperature 

-10°C -+40°C 

 

Operation

 

Both the Wireless Work Light and pocket light has three modes of operation which are all 

controlled via the on/off switch located on the reverse side of the work light & on the side of the 

pocket light. 

• Push the on/off switch once to activate the front spot light 

• Push the on/off switch a second time to activate the main light 

• Push and hold the on/off switch to dim the main light 

 

 

 

              

 

 

 

 

 

    

Locating Magnets

 

On/Off/Dim Switch 

 

Charge Indicator LEDs

 

Work Light

 

Pocket Light 

 

Summary of Contents for SP81499







Reviews: