SOYO SY-7IZM User'S Manual & Technical Reference Download Page 6

Page: 6 / 73

Introduction

SY-7IZM

SY-7IZM PLATFORM FEATURES

Board Size

4-layer PCB, 24.4x22.0cm(9.6”x8.7”), Micro-ATX

Form Factor

Socket 370

66/100MHz FSB

Celeron



Processor 300A~500 MHz

Built-in full speed 128KB L2 cache.

Features Auto-detection of CPU voltage

Chipset

440 ZX AGP Set

ATX Power

20-pin Male Connector

CPUFAN

3-pin CPU Cooling Fan Connector

Memory

DIMM Bank (DIMM1~2)

Two strips of 168-pin Unbuffered SDRAM DIMM

Supports 8/16/32/64/128MB DIMM modules in each

bank

Supports up to 256 MBytes of main memory

BIOS

System BIOS built-in, Award BIOS

APM, ACPI and "Plug-and-Play" function

Supports multiple-boot function

Onboard FLASH memory for easy upgrade

Bus Controller Compliant with PCI specifications version 2.1

PCI Slots

3 x 32-bit Bus Mastering Slots

ISA Slots

1 x 16-bit ISA Slots

IDE1, IDE2

2 x 40-pin Bus Mastering E-IDE/ATAPI Ports

IDE1: Primary IDE Device Connector

IDE2: Secondary IDE Device Connector

Supports Ultra DMA/33MHz

COM2

1 x 9-pin RS-232 Serial Connector

FDC

1 Floppy Disk Drive (FDD) Port

(Supports 1.2MB/1.44MB/2.88MB and LS120/3-mode FDD)

IR1

5-pin Serial Infrared Device Header

Keylock

5-pin KeyLock Header

Reset

2-pin Reset Switch Header

Speaker

4-pin PC Speaker Header

TB_LED

2-pin Turbo LED Header

All manuals and user guides at all-guides.com

all-guides.com

Summary of Contents for SY-7IZM










































































Search results

Summary of Contents for SY-7IZM

Reviews:

SOYO SY-7IZM, User'S Manual & Technical Reference, Page: 6 / 73

Search results

Summary of Contents for SY-7IZM

Reviews: