manualshive.com logo in svg

SOYO SY-7IZM, User'S Manual & Technical Reference, Page: 45 / 73

Share
Download
SOYO SY-7IZM User'S Manual & Technical Reference Download Page 45

BIOS Setup Utility

SY-7IZM

42

3-4.1 CHIPSET FEATURES SETUP
CHIPSET
FEATURES

Setting

Description

Note

Disabled

Auto
Configuration

Enabled

It is strongly recommended
to enable this option so that
the system automatically
sets all chipset feature
options on the left panel of
the screen (except for cache
update & BIOS cacheable).

Default

SDRAM Precharge
Control

Disabled

Enabled

Use the default setting

Default

Disabled

System BIOS
Cacheable

Enabled

The ROM area F0000H-
FFFFFH is cacheable.

Default

Disabled

Video BIOS
Cacheable

Enabled

The video BIOS C0000H-
C7FFFH is cacheable.

Default

Disabled

Default

Video RAM
Cacheable

Enabled

The ROM area A0000-
BFFFF is cacheable.

8 BIT I/O
Recovery Time

1

Use the default setting

Default

16 BIT I/O
Recovery Time

1

Use the default setting

Default

Disabled

Default

Memory Hole At
15M-16M

Enabled

Some interface cards will
map their ROM address to
this area. If this occurs,
select [Enabled] in this field.

Disabled

Passive Release

Enabled

Use the default setting

Default

All manuals and user guides at all-guides.com

Summary of Contents for SY-7IZM










































































Reviews:

No comments