background image

      DANGER

:

 Electrical Shock Hazards.

•  Only qualified persons should operate the MAXIS

® 

Feeder.

•  Wear eye protection, hard hat, cut resistant gloves and safety 
    toe shoes when using this tool.
•  Do not use tool while tired or under the influence of drugs, 
    alcohol, or medication.
•  Keep body parts and loose clothing away from moving parts.
•  Always follow safety procedures when operating.
•  Avoid accidental starting. Make sure switch is off before 
    plugging in motor.
•  Keep hands clear when lowering tension lid.
•  Keep hands away from rollers when tool is in operation.
•  Turn off motor before opening tension lid.

•  HEAVY- Use eye hooks and straps to load and unload.

 

•  Do not expose power tools to rain or wet conditions. Water 
    entering a power tool can increase the risk of electric shock.
•  Plug into a (GFCI) ground fault interrupted circuit outlet only.
•  If using Triggers

® 

. do not put in standing water.

•  Use a 10/3 20 AMP 120 Volt extension cord no more than 100 
    feet in length.
•  Maintain proper care of power cords. Do not use the cord to 
    carry the tool or pull the plug from an outlet. Replace damaged 
    cords immediately. Damaged cords can increase the risk of 
    electric shock.
•  Do not use this tool near live circuits. Shut off and lock out power 
    when working near existing circuits.

FAILURE TO OBSERVE THESE WARNINGS CAN

RESULT IN SEVERE INJURY OR DEATH.

WARNING

 - Personal Safety Hazards

WARNING

•  Read and understand all instructions and safety information in 
    this manual before operating or servicing this tool. 

3

IMPORTANT SAFETY INFORMATION

FAILURE TO OBSERVE THESE WARNINGS COULD 

RESULT IN SEVERE INJURY OR DEATH.

     WARNING

:

 Tool Use Hazards

•  Use this tool for the manufacturers intended purpose only. 
    Use other than that which is described in this manual can result 
    in injury or property damage.
•  Inspect all aspects of the pull to ensure safety.
•  Only qualified personnel should use MAXIS

® 

Feeder.

4

IMPORTANT SAFETY INFORMATION

     WARNING

:

 Entanglement Hazard

•  Do not operate this tool while wearing loose-fitting clothing.
    Retain long hair.
•  Keep hands away from the rollers and areas that contain chain 
    access and sprockets.
•  Turn off drill motor prior to opening tension lid.

FAILURE TO OBSERVE THESE WARNINGS CAN RESULT

IN SEVERE INJURY OR DEATH.

FAILURE TO OBSERVE THESE WARNINGS CAN RESULT

IN SEVERE INJURY OR DEATH. 

FAILURE TO OBSERVE THESE WARNINGS CAN RESULT

IN SEVERE INJURY OR DEATH.

Summary of Contents for MAXIS MCF-01








Reviews: