background image

      DANGER

:

 Electrical Shock Hazards.

•  Only qualified persons should use 

MAX PUNCH™

 360 Hydraulic 

    Punch.
•  Wear eye protection, hard hat, cut resistant gloves and safety
    toe shoes when using this tool.
•  Do not use tool while tired or under the influence of drugs, 
    alcohol, or medication.
•  Keep body parts and loose clothing away from moving parts.
•  Always follow safety procedures as shown in this manual.
•  Keep hands clear of cup and cutter when in operation.
•  Keep all body parts clear of handle’s path when not is storage 
    position.

 

•  This is not an insulated tool, contact with live circuits could 
   result in severe injury or death.

FAILURE TO OBSERVE THESE WARNINGS  CAN RESULT 
IN SEVERE INJURY OR DEATH

 Personal Safety Hazards

WARNING

•  Read and understand all instructions and safety information in 
    this manual before operating or servicing this tool. 

IMPORTANT SAFETY INFORMATION

FAILURE TO OBSERVE THESE WARNINGS COULD 
RESULT IN SEVERE INJURY OR DEATH

     WARNING

:

 Tool Use Hazards

•  Use this tool for the manufacturers intended purpose only. 
    Use other than that described in this manual can result in injury 
    or property damage.
•  Inspect all aspects of the electrical box to ensure safety.
•  Only qualified personnel should use knockout equipment.
•  Keep all decals clean and legible, and replace when necessary.

    CAUTION:

•  

Read and understand all of the instructions and safety information 

    in this manual before operating or servicing this tool.

    CAUTION:

•  Do not use if the cutters are damaged as this can cause binding 
    leading to tool malfunction.
•  If tool is in disrepair, DO NOT USE. Have tool serviced at an 
    Authorized Southwire Repair Center

Make sure bystanders are clear of the work area when performing 
knockouts. Nearby personnel can be injured if there is flying debris.

FAILURE TO OBSERVE THESE CAUTIONS CAN RESULT IN 
INJURY OR PROPERTY DAMAGE

FAILURE TO OBSERVE THESE CAUTIONS CAN RESULT IN 
INJURY OR PROPERTY DAMAGE 

IMPORTANT SAFETY INFORMATION

     WARNING

:

 Entanglement Hazard

•  Do not operate this tool while wearing loose fitting clothing. 
    Retain long hair.
•  Keep hands away from cup and cutters while operating punch. 
    Could pinch or crush hands.
•  Do not add extensions (cheaters) to the handles. Using 
    excessive force may result in injury or damage to the tool. 
    If excessive force is required, check and verify proper set up 
    instructions.

FAILURE TO OBSERVE THESE WARNINGS CAN RESULT
IN SEVERE INJURY OR DEATH. 

3

4

     WARNING

FAILURE TO OBSERVE THESE WARNINGS CAN RESULT 
IN SEVERE INJURY OR DEATH

FAILURE TO OBSERVE THESE WARNINGS CAN RESULT 
IN SEVERE INJURY OR DEATH

Summary of Contents for MAX PUNCH 360







Reviews: