Southwire 779765 Operating And Maintenance Instructions Manual Download Page 2

1

TABLE OF CONTENTS

Important Safety Information ..................................................2-4
Introduction.................................................................................5
Dimensions………………….……………………..……………...5-6
Assembly....................................................................................6
Setup and Operation.............................................................6-12
Servicing...................................................................................13
Troubleshooting and Maintenance......................................13-14
Warranty..............................................................................15-16

2

SAFETY ALER

T SYMBOLS

These symbols

                           are used to call attention to hazards or unsafe 
practices related that could result in injury or property damage. 
The three safety words defined below indicate the severity of the 
hazard. The message after the signal word provides information for 
preventing or avoiding the hazard.

DANGER - Immediate hazards that if not avoided WILL 
result in severe injury or death

WARNING - Hazards that if not avoided COULD result in 
severe injury or death

CAUTION - Hazards or unsafe practices that, if not 
avoided 

MAY result in severe injury or death

SAFETY FIRST

Safety is essential in the use and maintenance of Southwire Con-
tractor Equipment. This instruction manual and any markings on the 
tool provide information for avoiding hazards and unsafe practices 
related to the use of this tool. Observe all the safety information 
provided.

Summary of Contents for 779765










Reviews: