background image

Whisper H-80 Manual 

Document #0022 REV B 

SOUTHWEST WINDPOWER 

2/4/2001 

Installation 

To

w

er 

Wind Generator Model 
 
 

H80-24 

 Battery System Volts 
 

24 

Minimum Amp x Hours  
 (20 hour rate) 
 

200 

 

 Min. kwh (Volts x Amps x Hours/1000) 
 
 

Tower height minimum: 7m (20 ft) above trees or obsta-

cles within 100m (300 ft). 

100m (300 ft) 

1. TOWER LOCATION/TYPE AND 

HEIGHT. INSTALL TOWER 

(Install tower following manufacturer’s instructions.)

 

 
Tower height minimum is 7 meters (20 feet) above trees or 
obstacles within 100m (300ft). The lateral thrust rating at 
top must match wind generator model. The highest point 
on your property is generally best, but wind generator dis-
tance to battery and the battery voltage determine the cor-
rect  wire size (Refer to wire size table pg. 5). A self sup-
porting tower occupies less ground area than a guyed tower 
but is more expensive. A fold over design permits easy in-
stallation and maintenance on the ground and eliminates 
the need for climbing. 
 
Whisper Models H80 are suitable for roof or side-of-
building mounting on 

unoccupied

 buildings such as ga-

rage or barn. Some vibration transmission will be notice-
able from mounts to structure. Foundations must be de-
signed and approved for local wind/soil conditions. 

1. INSTALLATION 

DO THE FOLLOWING STEPS IN ORDER AND CIRCLE WHEN COMPLETE 
 

Roof Mount 

Side of Building Mount 

H80 

Mounting 

Bracket 

2. 

PURCHASE BATTERIES OF PROPER SIZE.  

 

Packages contains suggested battery size. See Table below

 

for minimum battery size. 

 MINIMUM BATTERY SIZES 

Summary of Contents for Whisper H-80


























Reviews: