background image

11

All commands must be terminated by a carriage return. All commands are repeated out the serial 

port to pass to the next controller or device. The “E“ symbol means that those command values are 

stored in EEPROM and will load on power up. 

COMMAND SETTINGS

COMMAND

 

ACTION

NOTES

 

ess 

Night Sky 

Night Sky in 3D perspective 

ess1

Night Sky 50%

Night Sky in 3D perspective at 50% brightness

es2

Scintillation 

Scintillation

es3

Tropical Winds 

Tropical Winds - Fast Sparkle 

esr

Rain Shower

Stars in Rain Shower mode 

est

Party Mode 

Stars all on with strobe/fade out pattern 

esldxxx     *E

Stars on Solid

xxx is the level, 1 - 255, 255 is the brightest

ecn 

Constellations on Solid

All LED’s on solid - separate than star commands

ecsp

Constellation Sparkle

Constellations sparkle

eco

Constellation O

ff

Only Constellations turn o

ff

eclvxxx     *E

Constellation Solid Level

xxx is the level, 1 - 255, 255 is the brightest

!

Trigger Shooting Star

Immediately trigger shooting star

ssj

Shooting Star 10 Seconds

Shooting Star every 10 seconds, Adjustable via RS-232 

ss1

Shooting Star 1 Minute

Shooting Star every minute

ss2

Shooting Star 2 Minutes

Shooting Star every 2 minutes

ss5

Shooting Star 5 Minutes

Shooting Star every 5 minutes

ssz

Shooting Star 10 Minutes

Shooting Star every 10 minutes

sso

Shooting Star O

ff

Boards in shooting star mode will turn o

ff

ssg

Shooting Star On

Shooting star on

mso

Meteor Shower On

Meteor Shower mode (DIP switches must be set correctly) Default rate is every 2 minutes

msf

Meteor Shower O

ff

Stops the meteor shower

ssd

Power on Setting

Return to Power on DIP Switch Setting

esdmxxx      *E

Dim Setting (stars only)

Brightness level of stars, 1 to 255, Default is 255 (brightest)

espkxxx       *E

Star Sparkle Speed

Sparkle Speed, 0 - 255, default is 17, the higher the number, the slower the sparkle

mtspxxx     *E

Meteor Shower Speed

xxx is the The Speed of the Meteors in the Shower, 0 - 255, Default is 50 (higher is slower)

mttmxxx     *E

Time Between Meteors

Time in 1/10’s of a second between each meteor in the shower (0-255) default is 7

mtinxxx     *E

Meteor Shower Interval

Time in seconds between meteor showers (0-255) default is 120

mtnmxxx     *E

Meteor Number

Number of meteors per shower (1-255) default is 19

ssspxxx       *E

Shooting Star Speed

xxx = 0 (fastest) to 254 (slowest), default is 40

sstmxxx       *E

Shooting Star Interval

Interval Between Shooting Stars in seconds, 0 - 255, Default is 10

eso

Stars O

ff

All Stars O

ff

esn

Stars On

Turns on the stars in the last mode they were in

globalo

ff

All O

ff

All Stars o

ff

, regardless of mode

NOTE:

The Epic Star Boards will read the DIP switch setting on power up, check that the boards are in the right mode before 

installing in a ceiling.

Summary of Contents for Fiber Optic Star













Reviews: