background image

45

TRACTOR -- MODEL NUMBER SO1538A, PRODUCT NO. 954 56 97-21

MOWER DECK

KEY   PART               
NO.    NO.                 DESCRIPTION

NOTE:  

All component dimensions given in U. S. 

      inches 1 inch = 25.4 mm

KEY   PART               
NO.    NO.                 DESCRIPTION

1         170280              Mower Housing Assembly
2         72140506          Bolt Carriage 5/16-18 x 3/4
3         138017              Bracket Asm Fr. Sway Bar
4         169970              Bracket Deck Sway Bar 38"/42" 
5         4939M               Retainer Spring
6         178024              Bar Sway Deck
8         850857              Bolt  3/8-24 x 1.25 Gr. 8
9         10030600          Washer, Lock 3/8
10       140296              Washer, Hardened
                                    (The following blades are available)
11       134148              Blade, 38" Mulching Std 
                                    (For mulching mowers only)
- -        139774              Blade, 38" Mulching Premium  
                                    (For better wear when mulching)
- -        138497              Blade, 38" Hi-Lift 
                                    (For bagging and discharging)
13       137645              Shaft Assembly, Mandrel,  
                                   Vented (Includes Key Number 6)
14       128774              Housing, Mandrel, Vented
15       110485X           Bearing, Ball, Mandrel
16       174493              Stripper, Vented Mower Deck
19       132827              Bolt, Shoulder
21       73680500          Nut
23       137607              Bracket, Mower Defl ector
24       105304X           Cap, Sleeve
25       123713X           Spring, Torsion, Defl ector
26       110452X           Nut, Push
27       106736X428     Shield, Defl ector
28       19111016          Washer  11/32 x 5/8 x 16 Ga. 
29       106735X           Rod, Hinge
30       173984              Screw Thdrol. Washer Head 
31       129963              Washer, Spacer
32       153532              Pulley, Mandrel
33       178342              Nut, Toplock 
36       131494              Pulley, Idler, Flat
40       73680600          Nut, Crownlock 3/8-16 unc
45       4497H               Retainer
53       130840              Brake Assembly
54       178515              Washer, Hardened

55       133840              Idler Arm Assembly 
56       165723              Spacer, Retainer
67       106932X           Knob 
68       144200              V-Belt, 42" Mower
69       76020312          Pin, Cotter 3/32 x 3/4
86       7631J                Runner, LH
87       128772              Runner, RH
88       19111216          Washer 11/32 x 3/4 x 16 Ga.
89       19131612          Washer 13/32 x 1 x 12 Ga.
96       74930620          Bolt 3/8-16 x 1-1/4 Mulcher
97       73930600          Nut Centerlock 3/8-16 unc
107     133502              Spacer Retainer
108     133503              Stiffener, Idler Arm
109     74760640          Bolt, Hex Hd 3/8-16 x 2-1/2
110     142587              Upstop Deck Front 38"
113     17060512          Screw 5/16-1/ x 3/4
122     131289              Rod, Brake LH
123     169971              Rod, Brake RH
146     165891              Bolt Carriage Idler
148     169022              Spring Return Idler
149     165898              Retainer Spring Yellow
150     19091216          Washer 9/32 x 3/4 x 16 Ga.
151     169670              Bracket Clutch Cable
152     172758              Clutch Cable 38"/46"
153     169674              Washer Flat 3/8" Type B
154     169675              Spring Retainer
155     169671              Spring Retention LVR CLTCH  
                                    CAB
156     169672              Spacer Clutch Cable
157     169669              Rod Clutch Cable 3/8"
158     17720408          Screw Hex Thd Cut 1/4-20 x 1/2
- -        130794              Mandrel Assembly (Includes  
                                    Housing, Shaft and Shaft Hard 
                                    ware Only-Pulley not Included)
- -        170317              Replacement Mower, Complete

For Parts Call K&T 606-678-9623 or 606-561-4983

www.mymowerparts.com

Summary of Contents for SO1538A

















































Reviews: