background image

20

MUFFLER   

Inspect and replace corroded muffl er and 
spark arrester (if equipped) as it could cre-
ate a fi re hazard and/or dam age.

SPARK PLUG(S) 

Replace spark plug(s) at the beginning 
of each mowing season or after every 
100 hours of operation, whichever occurs 
fi rst.  Spark plug type and gap setting are 
shown in “PROD UCT SPEC I FI CA TIONS” 
section of this manual.

Fuel Filter

Clamp

Clamp

IN-LINE FUEL FILTER 

The fuel fi lter should be replaced once 
each season.  If fuel fi lter becomes 
clogged, ob struct ing fuel fl ow to car bu -
re tor, re place ment is re quired.
1.   With engine cool, remove fi lter and 

plug fuel line sec tions.

2.   Place new fuel fi lter in position in fuel 

line with arrow pointing towards carbu-
retor.

3.   Be sure there are no fuel line leaks and 

clamps are properly positioned.

4.   Immediately wipe up any spilled gaso-

line.

AIR FILTER

Your engine will not run properly using a 
dirty air fi lter.  Replace pre-cleaner after 
every 25 hours of operation or every 
season.  Service paper cartridge every 
100 hours of operation or every season, 
whichever occurs fi rst.
Service air cleaner more often under dusty 
conditions.
1.   Pull up on air fi lter cover handle and 

rotate towards engine.

2.   Remove cover.
3.   Carefully remove air fi lter cartridge and 

pre-cleaner from base.

4.   Clean base carefully to prevent debris 

from falling into carburetor.

NOTE

: If very dirty or damaged, replace 

cartridge.
5.   Place new pre-cleaner and cartridge 

fi rmly in base.

6.   Align tabs on cover with slots in blower 

housing and replace cover.

7.   Hook handle on cover and push down 

on handle to close. 

IMPORTANT: 

 Petroleum solvents, such 

as kerosene, are not to be used to clean 
the cartridge.  They may cause de te ri o -
ra tion of the cartridge.  Do not oil car-
tridge.  Do not use pressurized air to clean 
cartridge.

Slots

Tabs

Base

Cartridge

Pre-cleaner

Cover

Handle

CLEANING

•   Clean engine, battery, seat, fi nish, etc. 

of all foreign matter.

•   Keep fi nished surfaces and wheels free 

of all gasoline, oil, etc.

•   Protect painted surfaces with au to -

mo tive type wax.

We do not recommend using a garden 
hose or pressure washer to clean your 
tractor unless the engine and transmis-
sion are covered to keep water out. Water 
in engine or transmission will shorten the 
useful life of your tractor.  Use compressed 
air or a leaf blower to remove grass, 
leaves and trash from tractor and mower.

Clean out chaff and debris

02744

Air Screen

ENGINE COOLING SYSTEM 

Debris may clog the engine’s air cooling 
system. Remove blower housing and clean 
area shown to prevent overheating and 
engine damage.

For Parts Call K&T 606-678-9623 or 606-561-4983

www.mymowerparts.com

Summary of Contents for SO1538A

















































Reviews: