background image

 

 

Page 1 of 21 

Summary & Introduction 

 

 

 

Summary & Introduction 

Important 

The information contained herein is general in nature and not intended for specific application purposes. It 

does not relieve the user of responsibility to use sound practices in application, installation, operation, and 

maintenance of the equipment purchased.  Southern States reserves the right to make changes in the 

specifications shown herein or to make improvements at any time without notice or obligation. Should a 

conflict arise between the general information contained in this publication and the contents of drawings or 

supplementary material, or both, the latter shall take precedence.

 

 

 

Summary 

These instructions do not purport to cover all details or variations in equipment, or provide for every possible 

contingency to be met in connection with installation, operation, or maintenance. Should information be 

desired, or should particular problems arise which are not covered sufficiently for the purchaser’s purposes, 

the matter should be referred to the local Southern States Representative. 

The contents of this instruction manual should not become part of or modify any prior or existing agreement, 

commitment, or relationship.  The sales contract contains the entire obligation of Southern States.  The 

Warranty contained in the contract between the parties is the sole warranty of Southern States.  Any 

statements contained herein do not create new warranties or modify the existing warranty. 

 

 

Summary of Contents for ESD63



























Reviews: