background image

10

MAINTENANCE
SCHEDULE

FILL IN DATES
AS YOU COMPLETE
REGULAR SERVICE

Check Engine Oil Level

Change Engine Oil

Oil Pivot Points

Inspect Air Screen

Inspect Spark Arrester / Muffler

Clean or Replace Air Cleaner Cartridge

Clean Engine Cylinder Fins

Replace Spark Plug

BEFORE EACH USEEVERY 25 HOURS

EVERY 5 HOURS EVERY 50 HOURS

SERVICE DATES

2

1 - Change more often when operating under a heavy load or in high ambient temperatures.
2 - Service more often when operating in dirty or dusty conditions. 

MAINTENANCE

c

SAE 30 OR 10W-30 MOTOR OIL 

d

REFER TO MAINTENANCE “ENGINE” SECTION

LUBRICATION CHART

d

 EN GINE

c

 TINE  CON TROL

c

 IDLER

  ARM

GENERAL RECOMMENDATIONS

The warranty on this tiller does not cover items that  have 
been subjected to operator abuse or negligence.  To receive 
full value from the warranty, the operator must main tain tiller 
as instructed in this manual.

Some adjustments will need to be made periodically to 
properly maintain your tiller.

At least once a season, check to see if you should make 
any of the adjustments described in the Service and Ad-
justments section of this manual.
•      Once a year you should replace the spark plug, clean 

or replace air fi lter, and check tines and belts for wear.  
A new spark plug and clean air fi lter assure proper 
air-fuel mixture and help your engine run better and 
last longer.

BEFORE EACH USE

•      Check engine oil level.
•      Check tine operation.
•      Check for loose fasteners.

LUBRICATION

Keep unit well lubricated (See “LUBRICATION CHART”). 

For Parts Call K&T 606-678-9623 or 606-561-4983

www.mymowerparts.com

Summary of Contents for 96082000200



















Reviews: