Use the high-precision quality faders to control the output level
of the Alt 3-4 subgroup and main mix.
MAIN OUTPUTS
The MAIN outputs carry the MAIN MIX signal and are on
balanced XLR connectors with a nominal level of +4dBu.
7
ALT 3-4 OUTPUTS
The ALT 3-4 output are unbalanced and carry the signals of
the channels that you have assigned to this group using the
MUTE switch. This can be used to route a subgroup to a further
mixing console for example, or it could be used as a recording
output working in tandem with the main output. This means you
could record to four tracks simultaneously. The icing on the
cake, so to speak, is that you could connect Y-cables to these
four outputs and then connect your 8-track recorder in such a
way that you have 2 x 4 tracks. (E.g. Channel 1 feeds track 1and
track 2, etc.). In the first recording pass, you record on track 1,
3.5 and 7 and in the second pass, on tracks 2, 4, 6 and 8.
CONTROL ROOM OUTPUT
The control room output is normally connected to the monitor
system in the control room and provides the stereo mix or, when
required, the solo signal.
SERIAL NUMBER
Please note the important information on the serial number
given in chapter 1.3.3.
FUSE HOLDER
The console is connect to the mains via the cable supplied
which meets the required safety standards. blown fuses must
only be replaced by fuses of the same type and rating.
The mains connection is via a cable with IEC mains connector.
An appropriate mains cable is supplied with equipment.
IEC MAINS RECEPTACLE
POWER
Use the POWER switch to power up the mixing the console.
PHANTOM
The PHANTOM switch activates the phantom power supply
for the XLR connectors of the mono channels which is required
to operate condenser microphones. The red +48 VLED lights up
when phantom power is on. As a rule, dynamic microphones
can still be used with phantom power switched on, provided
that they are wired in a balanced configuration. In case of doubt,
contact the microphone manufacturer!
After the phantom power supply has been switched
on, do not connect microphones to the mixer (or the
stagebox/wallbox). Connect the on. In addition, the
monitor/PA loudspeakers should be muted before
activating the phantom power supply. After switching
on, wait approx. One minute to allow the system to
Stabilize.
Caution! You must never use unbalanced XLR
connectors (PIN 1and 3 connected) on the MIC
input connectors if you want to use the phantom
power supply.
2.4 Rear view of
NEOMIX-402UFX / NEOMIX-802UFX
2.4.1 main mix outputs, Alt 3-4 outputs and
control room outputs
Fig. 2.14 Main mix outputs, Alt 3-4 outputs and
control room outputs
2.4.2 Voltage supply, phantom power and fuse
Fig. 2.15: Voltage supply and fuse
Fig. 2.16: USB
NEOMIX-402UFX / NEOMIX-802UFX
PIN 2 = HOT / PIN 3 = COLD
MAIN OUTPUTS
R
L
ALT 3-4 OUTPUTS
4
3
CONTROL ROOM OUT
R
L
DIGITAL
OPTIC
DIGITAL
INPUT
COAXIAL
COAXIAL
DIGITAL
OUTPUT
100 - 240 V ~ 50/60 Hz 40W
FUSE: T1.6 AH 250V
POWER
ON
PHANTOM
ON
USB
/
DIGITAL
INTERFACES
NEOMIX
402UFX/802UFX
offer
the
maximum
flexibility
for
your
recor-
ding
purpose.
You
can
connect
your
NEOMIX
mixer
with
a
PC
or
MAC
via
the
USB
soundcard
or
with
other
equipment
via
optical/coaxial
digital
inputs.
USB
I/O
INTERFACE
Connect
your
PC
or
MAC,
no
specific
driver
is
needed
and
your
compu-
ter
will
automatically
recognize
the
NEOMIX
USB
interface.
Please
note
your
NEOMIX
will
be
assinged
to
windows/MAC
peripheral
as "USB
headphone"
and
"USB
microphone"
or
similar.
You
can
use
the
Audacity
software
included
in
the
package
or
any
other
recording
software.
Make
sure
to
configure
properly
the
software
input
and
outputs
with
the
above
mentioned
USB
headphone/USB
micro-
phone.
Please
refer
to
software
manual
for
detailed
configuration
instruction.
The
overall
mixer
signal
can
be
recorded
by
your
software
with
all
the
channels
togheter
in
addition
to
any
eventual
track
played
on
the
com-
puter.
The
Software
output
to
channel
5/6
and
control
the
Volume/
Equalization
for
monitoring
purpose
.
Eventually
you
can
also
hear
the
software
playback
and
any
eventual
channel
signal
on
the
mixer
channel
or
aux
in
to
the
main
mix,
for
example
if
you
intend
to
play
live
a
guitar
or
to
sing
with
a
microphone
along
with
a
backing
track
on
your
PC.
DIGITAL
CONNECTIONS
With
the
coaxial
or
optical
input,
you
can
connect
any
external
digital
source
(
for
instance
DVD
players
)
and
record
them
directly
in
your
computer.
The
input
can
be
selected
between
coaxial
and
digital,
both
connection
at
the
same
time
are
not
allowed.
Please
note
that
you
won't
hear
the
digital
input
signal
in
the
main
MIX
while
recording,
but
your
software
does
and
you
can
later
play
it
back
after
recorded.
Important:
to
record
digital
interface
you
also
need
to
connect
with
a
software
with
the
USB
interface
NEOMIX
402UFX/802UFX
also
provide
a
digital
output
which
may
be
useful
to
connect
other
equipment,
such
as
digital
recorders.
Please
note
that
in
this
case
only
the
digital
input
signal
is
routed
to
the
digital
output,
not
the
main
mix.
