2-TRACK INPUT
2-TRACK OUTPUT
These connectors are wired in parallel with MAIN OUT and
carry the main mix signal (unbalanced).Connect the 2-TRACK
OUTPUT to the inputs of your recording device. The final output
level can be adjusted via the high-precision MAIN MIX fader.
If you connect a compressor or a noise gate after
the 2-track output, the faders will probably not be
able to create a satisfactory fade-out effect.
The 2-TRACK INPUT RCA connectors are provided for
connecting a 2 track machine (e.g. DAT recorder). They can
also be used as stereo line input. Alternatively, the output
signal of a second mixer can also be connected.
If you connect a hi fi amplifier with a source selection switch
to the 2-TRACK
INPUT, you can easily switch between
additional sources (e.g. Cassette recorder, CD player, etc.).
You can use the SOLO switch to separately monitor the
aux sends via the CONTROL ROOM/PHONES outputs and
check these with the level metres.
SOLO
If you want to monitor the signal of just one AUX
bus, none of the other SOLO SWITCHES should be
pressed and the MODE switch must be in the SOLO
position (not pressed down).
AUX SEND 1
AUX SEND 2
STEREO AUX RETURN 1
5
If you use aux send 1 pre-fader, you would usually connect
the AUX SEND 1connector to monitors via a power amp (or an
active monitor system). If you use aux send 1 post-fader,proceed
as described under aux send 2.
The AUX SEND 2 connector outputs the signal you picked up
from the individual channels using the FX control. You can connect
this to the input of an effects mix is created, the processed signal
can then be routed from the effects device output back into the
STEREO AUX RETURN connectors.
The
return path for the effects mix generated using the post-fader aux send.
This is where you connect the output signal of the external effects device.
If only the connector is used, the AUX RETURN automatically operates
STEREO AUX RETURN 1 connectors generally serve as the
in mono.
If you wish to use the internal effects processor,
no connectors should be plugged into STEREO
AUX RETURN 2.
In this instance, the FX control of the channel being
used as an effects return should be turned fully
counterclockwise, otherwise feedback problems
could occur!
STEREO AUX RETURN 1 is a stereo control which determines
is used as effects return, you can add the effects signal to any
STEREO AUX RETURN 1
In this instance, the effects device should be set at
100% effect.
STEREO AUX RETURN MON
Monitor mix with effect
You can now use the STEREO AUX RETURN MON control to
adjust the level of the effects signal routed to the monitor mix.
The STEREO AUX RETURN 2 control determines the level of
signals fed into the AUX RETURN 2 connectors which are routed
to the main mix.
STEREO AUX RETURN 2 (FX)
MAIN MIX/ALT 3-4
The MAIN MIX/ALT 3-4 switch routes the signal connected to
STEREO AUX RETURN 2 to either main mix (not pressed) or
“
dry
”
channel signal .
The STEREO AUX RETURN MON control has a special
function: it can be used to add an effect to a monitor mix.
For example:
In this instance, the effect device should be set up as follows:
AUX SEND 2 is connected to the L/Mono input of your effects
device, while its outputs are connected to STEREO AUX RETURN
1. Connect the amplifier of your monitor system to AUX SEND 1.
The AUX SEND 1 master control determines the volume of the
monitor mix.
submix (Alt 3-4, pressed).
STEREO AUX RETURN 2
You can also use these connectors as additional
line inputs.
The STEREO AUX RETURN 2 connectors serve as the return
path for the effects mix generated using the FX control. If these
connectors already function as additional inputs, you can route
the effects signal back into the console via a different channel,
with the added benefit that the channel EQ can be used to adjust
the frequency of the effects signal.
2.3.2 Aux send connectors 1 and 2
2.3.3 Stereo aux return connectors
Fig. 2.8:
Stereo aux return connectors
Fig. 2.7: Aux send connectors
2.3.4 Stereo aux return
Fig. 2.9: Stereo aux return controls
2.3.5 Tape input/tape output
Fig. 2.10: 2-track connectors
1
2
FX
AUX SENDS
NEOMIX-402UFX / NEOMIX-802UFX
LEFT/MONO
RIGHT
1
2
RETURNS
STEREO AUX
IN
OUT
2-TRACK IN/OUT
L
R
L
R
1
2
1
STEREO AUX RETURNS
MAIN MIX
ALT 3-4
TO AUX
SEND 1
FX
- 8
0
+
8
- 8
0
+
8
- 8
0
+
8
