Soundoff Signal nFUSE Manual Download Page 23

nFUSE™ LED Lightbar

nFUSE Lightbar English  0520

23.

CLEANING & CARE OF YOUR LIGHTBAR:

 

Keeping the lenses clean and scratch free will optimize the performance of 

the lightbar.  The exterior of the lightbar including lenses should be cleaned 

with mild soapy water and a soft cotton cloth to remove dirt, grime and 

insects.  Never use window cleaners or harsh chemicals on the lenses;  this 

may cause failure of the lenses or reduce clarity resulting in the reduction of 

light output.

MOUNTING INTEGRITY:

A review of bolt/hardware/mounting bracket integrity should be performed 

at the beginning and end of each shift.

WARNING

 - DRILLING ANY HOLES INTO THE LIGHTBAR IS NOT 

RECOMMENDED! THE RISK OF DAMAGING INTERNAL COMPONENTS 

AND THE RESULTING FAILURE OF THE LIGHTBAR WILL VOID ANY 

WARRANTY OF THIS PRODUCT.

WARNING

 - CARE MUST BE TAKEN WHEN DRILLING THROUGH 

THE ROOF OF THE VEHICLE NOT TO DRILL INTO ANY EXISTING 

WIRING AND NOT TO DRILL THROUGH THE HEADLINER OR SUPPORT  

MEMBERS OF THE VEHICLE.  CHECK BOTH SIDES OF THE MOUNTING 

SERVICE PRIOR TO DRILLING. DE-BURR ANY HOLES AND REMOVE 

ANY METAL SHARDS OR REMNANTS.  INSTALL GROMMETS INTO 

ALL WIRE PASSAGE HOLES.

WARNING

 - ROUTE WIRES ONLY IN LOCATIONS THAT ARE NOT 

SUBJECTED TO POTENTIAL WEAR.  MAKE SURE TO AVOID ROUTING 

WIRES IN THE DEPLOYMENT AREA OF YOUR AIR BAG. REFER TO 

YOUR VEHICLE OWNER’S MANUAL FOR AIR BAG DEPLOYMENT 

ZONES.

WARNING

 - ALL CUSTOMER SUPPLIED POWER WIRES CONNECTING 

TO THE POSITIVE (+) OR NEGATIVE (-) BATTERY TERMINAL OR 

LOCAL CHASSIS GROUND (-) MUST BE SIZED TO SUPPLY AT LEAST 

125% OF THE MAXIMUM CURRENT AND PROPERLY FUSED AT THE 

POWER SOURCE WITH APPROPRIATELY RATED FUSE.

IMPORTANT:

  When passing cables through fire wall or other sheet 

metal, insert grommet to protect the cable!

WARRANTY RETURN PROCESS:

Please contact your SoundOff Signal Sales Representative, Customer Services 

staff or our Technical Department (800.338.7337) for a RMA #, Return 

Merchandise Authorization Number.  

The following information is required for issuance of the RMA #:

•  Reason for returning the product*

•  Address where replacement product is to be shipped*

•  Telephone number where you may be reached*

•  SoundOff Signal invoice number on which product was purchased**

•  SoundOff Signal part number and serial number**

•  E-mail address where  RMA # should be e-mailed**

•  Fax number where  RMA # should be faxed**

* RMA # will not be given without this information.

** If available, please provide this information.

SoundOff Signal will NOT accept returns without an  RMA #. Each  RMA # 

is good for only one (1) return and will expire (30) days after the date it was 

issued. Products must be shipped back to SoundOff Signal and the RMA # 

clearly marked on the outside of the package near the shipping label. Please 

use the following address on your shipping label:

   

SoundOff Signal

   

ATTN:   RMA # / Technical Services

   

3900 Central Parkway

   

Hudsonville, MI  49426

WARRANTY EXCLUSIONS:

Shipping & Handling, labor and service fees are non-refundable. SoundOff 

Signal is not liable for any damage due to installation or personal injury as a 

result of using SoundOff Signal product. 

WARRANTY FORFEITURE:

Warranty will not be granted if the Warranty Return Policy & Procedure rules 

are not strictly followed. Physical damage resulting from customer abuse 

will void warranty. Warranty will also be voided if any SoundOff Signal and/

or manufacturer serial tags, product stickers, seals, or the like, are removed, 

altered or tampered with. Returned product that is damaged by shipping via 

the RMA # procedure is not the responsibility of SoundOff Signal.

Document effective date on cover and below supersedes previously dated 

policies and statements.  

There are no other warranties, expressed or implied, including, but not limited 

to, any implied merchantability or fitness for a particular use. SoundOff 

Signal reserves the right to modify this warranty statement at any time; or to 

discontinue, modify, or upgrade any products of its manufacture with design 

improvements without prior notice.

WARNING MESSAGES - PLEASE READ:

WARRANTY & RETURN GOODS PROCEDURE

NOTICE: 

Installers and users must comply with all applicable federal, state and local laws regarding use and installation of warning devices.

Improper use or installation may void warranty coverage.

To review our Limited Warranty Statement & Return Policy for this or any SoundOff Signal product, visit our website at 

www.soundoffsignal.com/tech-services/returns/

.

If you have questions regarding this product, contact 

Technical Services

, Monday - Friday, 8 a.m. to 5 p.m. ET at 

1.800.338.7337

 (press #4).

  Questions or comments that do not require immediate attention may be emailed to 

[email protected].

ENHANCING SAFETY THROUGH INNOVATION

Summary of Contents for nFUSE
























Reviews: