background image

6

If you experience a problem once the Subwoofer is installed use this guide to locate the trouble.

The radio is working, but the Subwoofer is not working:

•  Check the battery voltage to make sure it is not discharged below 11 volts.
•  Check the negative battery cable to see if it has been securely tightened back on the battery.
•  Check the inline fuse located near the battery to make sure it is plugged in completely, and not blown.
•  Check the 12Volt power-connector near the fi rewall to make sure it is plugged in securely.
•  Check the inline connectors near the subwoofer enclosure to make sure they are plugged securely.
•  Check the ground wire connection to make sure it is tightly secured to the proper ground in the vehicle.
•  Check the audio input signal connection to make sure it is secure and connected to the proper wiring.
•  Test with different music in case there is no low frequency audio in the initial sound check.

There is a buzz or rattle noise that accompanies the low frequency element of the music:

•  Check for a connector or any other object that could be very near the enclosure.
•  Check the subwoofer enclosure mounting brackets to make sure they are secure.

Symptom

Possible Cause

Solution

No Subwoofer Output

Fuse not installed in inline fuse 
holder on subwoofer and / or amp 
harness

Install fuse into fuse holder.  
Refer to instructions for correct 
placement

Low battery voltage

Recharge the battery

Negative battery cable not 
connected

Reconnect negative battery cable

Power wire connector not 
connected to body harness

Connect power wire to body 
harness.  Check for loose 
connection

Ground wire not grounded properly

Check ground wire with voltmeter 
to insure it is a good ground

Balance or fader controls not set to 
neutral position

Set balance and fader control to 
center settings. (only effects stand 
alone subwoofer kit)

No low frequency information in 
music

Test with several different songs

Subwoofer harness not properly 
/ completely connected to sub-
woofer.

Securely fasten both of the 
connectors on the subwoofer 
harness to the subwoofer. Check 
for loose connections.

Radio Not Coming On

Blown radio fuse

Refer to owner's manual for radio 
fuse location and value

Low battery voltage

Recharge the battery

Summary of Contents for SSICRE07











Reviews: