SoundFreaq SFQ-09 User Manual Download Page 3

 

18. 

Do not place any naked flame sources, 
such as lighted candles, on the apparatus. 

19. 

The battery used in this product must be 
properly recycled or disposed of. Please 
contact your local recycling center for 
proper battery handling and disposal 
instructions.

 

FCC and IC Information: 

This device complies with Part 15 of the FCC 
Rules and RSS-210 of the IC Rules. Operation 
is subject to the following two conditions: (1) 
This device may not cause harmful interference, 
and (2) this device must accept any interference 
received, including interference that may cause 
undesired operation. 

Canada IC statments 

Le présent appareil est conforme aux CNR 
d'Industrie Canada applicables aux appareils 
radio exempts de licence. L'exploitation est 
autorisée aux deux conditions suivantes: (1) 
l'appareil ne doit pas produire de brouillage, et 
(2) l'utilisateur de l'appareil doit accepter tout 
brouillage radioélectrique subi, même si le 
brouillage est susceptible d'en compromettre le 
fonctionnement. 
 

Warning: 

Changes or modifications to this unit 

not expressly approved by the party responsible 
for compliance could void the user's authority to 
operate the equipment. 
 

Note: 

This equipment has been tested and 

found to comply with the limits for a Class B 
digital device, pursuant to Part 15 of the FCC 
Rules. 
These limits are designed to provide reasonable 
protection against harmful interference in a 
residential installation. This equipment 
generates, uses, and can radiate radio 
frequency energy and, if not installed and used 
in accordance with the instructions, may cause 
harmful interference to radio communications. 
However, there is no guarantee that 
interference will not occur in a particular 
installation. If this equipment does cause 
harmful interference to radio or television 
reception, which can be determined by turning 
the equipment off and on, the user is 
encouraged to try to correct the interference by 
one or more of the following measures: 

 

Reorient or relocate the receiving antenna. 

 

Increase the separation between the 
equipment and receiver. 

 

Connect the equipment into an outlet on a 
circuit different from that to which the 
receiver is connected. 

 

Consult the dealer or an experienced radio 
TV technician for help. 

 
Warnings: 

The device meets the exemption 

from the routine evaluation limits in section 2.5 
of RSS 102 and users can obtain Canadian 
information on RF exposure and compliance 
from the Canadian Representative Burnport 
Holdings Ltd. 72MT Belcher Pls, East, Calgary, 
Alberta, T2Z 2G1, CANADA. Tel: 403-257-4961 

FCC&IC Radiation Exposure 
Statement 

This equipment complies with FCC radiation 
exposure limits set forth for an uncontrolled 
environment and meets the exemption from the 
routine evaluation limits in section 2.5 of RSS 
102. 

1. 

This Transmitter must not be co-located or 
operating in conjunction with any other 
antenna or transmitter. 

2. 

This equipment complies with FCC RF 
radiation exposure limits set forth for an 
uncontrolled environment. This equipment 
should be installed and operated with a 
minimum distance of 20 centimeters from 
user and bystanders. 

Le dispositif rencontre l'exemption des limites 
courantes d'évaluation dans la section 2.5 de 
RSS 102 et la conformité à l'exposition de 
RSS-102 rf, utilisateurs peut obtenir 
l'information canadienne sur l'exposition et la 
conformité de rf.   
For compatibility between the system and 
another device with Bluetooth technology, 
consult the device's documentation and dealer. 
In some countries, there may be restrictions on 
using Bluetooth devices. Check with your local 
authorities. 
 

is a registered trademark of Bluetooth 

SIG, Inc 

 

Please read rating label at the bottom of system 
for power input and other safety information. 

Summary of Contents for SFQ-09





















Reviews: